Forum: Model A (1928-31)
01-12-2021, 01:30 PM
|
|
Replies: 10
Views: 494
|
|
Forum: Model A (1928-31)
01-11-2021, 08:50 AM
|
|
Replies: 19
Views: 1,095
|
|
Forum: Model A (1928-31)
01-01-2021, 03:16 PM
|
|
Replies: 2
Views: 350
Clutch finger adjustment
When trying to adjust the fingers on the clutch plate, is the plate bolted to the flywheel and disc and the adjustment being between 5/8 & 11/16 after final adjustment Your answers are appreciated.
|
|
Forum: Model A (1928-31)
01-01-2021, 02:47 PM
|
|
Replies: 15
Views: 1,170
Re: Engine heat in cold weather
How did you arive that there was a difference in the engine temperature with the heater on or off? Are you running a temperature gangue?
|
|
Forum: Model-A
12-30-2020, 08:59 PM
|
|
Replies: 0
Views: 254
|
|
Forum: Model A (1928-31)
12-06-2020, 08:52 AM
|
|
Replies: 26
Views: 1,626
Re: Bad Stud thread
Bratton's supplies a tool jig kit #8235 that allows you to drill out the stud without disturbing or removing any of the other studs. The jig comes with a locating guide and bushings, a burr to center...
|
|
Forum: Model A (1928-31)
11-22-2020, 05:55 PM
|
|
Replies: 12
Views: 962
|
|
Forum: Model A (1928-31)
11-19-2020, 12:25 PM
|
|
Replies: 3
Views: 560
Re: Clutch finger depth
Is the 11/16 measurement with the plate and disc bolted to flywheel?
Thanks for a response.
|
|
Forum: Model-A
10-30-2020, 03:45 PM
|
|
Replies: 0
Views: 403
Used Model "A" Engine
I bought a used running engine sight unseen for a project car. The car owner changed his mind and decided on a rebuilt engine. After I received the engine prior to the customer changing his mind I...
|
|
Forum: Model-A
10-28-2020, 06:23 PM
|
|
Replies: 0
Views: 304
Pair of 30 and 31 Rear Fenders
For Pickup/Roadster/Coupe. Original very good condition. no dents / excellent beads / no rips. Sand/prime/paint and put on your car. Shipping additional or pick up.
|
|
Forum: Model-A
10-17-2020, 03:38 PM
|
|
Replies: 0
Views: 351
|
|
Forum: Model A (1928-31)
10-02-2020, 07:05 PM
|
|
Replies: 3
Views: 544
|
|
Forum: Model A (1928-31)
09-26-2020, 10:48 AM
|
|
Replies: 36
Views: 5,070
Re: Exhaust Manifold to Tailpipe gasket
Nobody has mentioned to loosen the tail pipe bracket at the rear to help with the alignment. This allows for a forward and rotational movement of the pipe.
|
|
Forum: Model A (1928-31)
09-23-2020, 05:51 PM
|
|
Replies: 3
Views: 454
Door striker plate screws on coupe
I want to replace the striker plate screws on a 30 coupe. My question is are the nuts on the screws captured? I don't want to find out the hard way.
All help is appreciated.
|
|
Forum: Model A (1928-31)
08-15-2020, 07:12 PM
|
|
Replies: 7
Views: 418
|
|
Forum: Model A (1928-31)
07-21-2020, 09:51 AM
|
|
Replies: 20
Views: 1,381
Re: Shifter spring compressor
I like your idea as the spring is totally contained by the rod and washers, expanded on your idea I would use a washer just a little larger then the OD of the spring and cut three notches equal...
|
|
Forum: Model A (1928-31)
07-15-2020, 05:18 PM
|
|
Replies: 9
Views: 715
Model A Bucking at 45 mph plus
Model A Bucking at 45 mph plus
The car is a A with indented firewall with a B engine, A head, converted to 12V, running a B carb and B distributor, 3.0-ohm coil, new condenser, cleaned...
|
|
Forum: Model A (1928-31)
04-13-2020, 04:39 PM
|
|
Replies: 21
Views: 1,655
|
|
Forum: Model A (1928-31)
02-18-2020, 08:40 PM
|
|
Replies: 10
Views: 1,070
|
|
Forum: Model A (1928-31)
12-26-2019, 09:34 AM
|
|
Replies: 3
Views: 852
Re: Shackle Bore Alignment
Since you have the spring in place leave the u-bolts loose which will give the spring a little movement to shift as you install shackles. Then with the spring spreader in place go back tighten the...
|
|
Forum: Model A (1928-31)
11-11-2019, 03:32 PM
|
|
Replies: 38
Views: 2,417
Re: 8 volt battery in 6 volt car
I am just looking for a knowledge based cause and effect of this set up has on the various electrical components of a Model A.
Sofield
|
|
Forum: Model A (1928-31)
11-10-2019, 05:30 PM
|
|
Replies: 38
Views: 2,417
8 volt battery in 6 volt car
If using a 8 Volt battery what is the effect on all the 6 volt parts?
Starter motor, all bulbs, coil, generator, horn, 6 volt signal stat, ammeter etc.
Your answers are appreciated.
|
|
Forum: Model A (1928-31)
11-07-2019, 07:25 PM
|
|
Replies: 35
Views: 3,630
Re: Club Thinning
I would like to see our club use a number of these suggestions to recruit new members
sofield
|
|
Forum: Model A (1928-31)
01-27-2019, 06:46 PM
|
|
Replies: 15
Views: 1,555
Re: Headlight wiring
If you don't have the tabs on the lower part of the radiator use black cable ties going through the core and fasten on the front side of the radiator.
Sofield
|
|
Forum: Model A (1928-31)
01-24-2019, 08:23 PM
|
|
Replies: 13
Views: 1,746
Re: Bad manifold gaskets
I will make the assumption that you are using gland rings in the four exhaust ports and the rings wont allow the manifold to seat properly between the manifold and block causing the gasket to leak...
|
