Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 41
Search took 0.01 seconds.
Search: Posts Made By: ghalperin
Forum: Model-A 04-15-2021, 01:48 PM
Replies: 0
Views: 234
Posted By ghalperin
Wico Magneto Model X

Good condition
Forum: Model-A 03-07-2021, 07:16 PM
Replies: 1
Views: 459
Posted By ghalperin
Re: Wanted: Winfield Dual intake manifold

Any brand manifold would be great.
Forum: Model-A 03-06-2021, 12:54 AM
Replies: 1
Views: 459
Posted By ghalperin
Wanted: Winfield Dual intake manifold

In search of a dual carburetor intake manifold for dual Winfield SR carbs. Thank you for any leads. glennhalperin@att.net

457511
Forum: Model A (1928-31) 03-24-2020, 05:33 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Re: Bronze Model A Ford Rear Main Thrust Plate & Oil Seal installation

Sorry to be misleading in my initial post. The engine has not been apart since the '70s. I was driving it a little too hard on the toll road and afterwards is when I noticed the nocking. All of the...
Forum: Model A (1928-31) 03-24-2020, 04:10 PM
Replies: 36
Views: 7,831
Posted By ghalperin
Re: Timing indicators, do you use them?

I know this is an old post, but are the Miss Victoria style indicators available anywhere?
Forum: Model A (1928-31) 03-24-2020, 04:00 PM
Replies: 44
Views: 10,256
Posted By ghalperin
Re: timing indicators

I know this is an old post, but are these indicators available anywhere?
Forum: Model A (1928-31) 03-24-2020, 03:34 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Re: Bronze Model A Ford Rear Main Thrust Plate & Oil Seal installation

After completely disassembling, adjusting all the babbett's and reassembling, it still knocked. I sent the rods out to have the wrist pin bushings changed. When I was cleaning it up for reassembly,...
Forum: Model A (1928-31) 02-23-2020, 04:06 PM
Replies: 48
Views: 6,851
Posted By ghalperin
Re: Water Temperature Gauge

Can you please post a photo or two?
Forum: Model A (1928-31) 01-28-2020, 06:38 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Forum: Model A (1928-31) 01-28-2020, 06:37 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Re: Bronze Model A Ford Rear Main Thrust Plate & Oil Seal installation

The engine was rebuilt in the '70s, I doubt if they're still around. The car was in Napa for decades.
Forum: Model A (1928-31) 01-27-2020, 10:36 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Re: Bronze Model A Ford Rear Main Thrust Plate & Oil Seal installation

Tonight I pulled the crankshaft and started whittling away. It took about 30 minutes with a breakaway utility knife. It almost looks like the end thrust was poured separately from the main bearing....
Forum: Model A (1928-31) 01-27-2020, 09:42 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Forum: Model A (1928-31) 01-27-2020, 07:25 PM
Replies: 13
Views: 1,719
Posted By ghalperin
Bronze Model A Ford Rear Main Thrust Plate & Oil Seal installation

My thrust clearance quadrupled after a 75 mile drive. Itís about .030 now.
420228
420229

I picked up this bronze Model A Ford Rear Main Thrust Plate & Oil Seal
420230

I searched for info on...
Forum: Model A (1928-31) 10-25-2019, 06:16 PM
Replies: 8
Views: 1,187
Posted By ghalperin
Re: Starter bench test spins slow

I figured out the problem. The brushes were loose on the field coils causing them to get hot and turn color. Quick disassemble, clean up connections, install heat shrink tubing and reinstall brushes....
Forum: Model A (1928-31) 10-24-2019, 04:54 PM
Replies: 8
Views: 1,187
Posted By ghalperin
Re: Starter bench test spins slow

My local parts house had Blue Magic brand. Iím going to try it.

410385
Forum: Model A (1928-31) 10-24-2019, 04:02 PM
Replies: 8
Views: 1,187
Posted By ghalperin
Re: Starter bench test spins slow

I am going to look into that.
Forum: Model A (1928-31) 10-24-2019, 02:26 PM
Replies: 8
Views: 1,187
Posted By ghalperin
Re: Starter bench test spins slow

Guys, thanks for the input. The bushings are tight enough and the only thing the looks like rubbing are the wiring for the brushes. They may have been polishing the end of the armature. See the...
Forum: Model A (1928-31) 10-24-2019, 10:44 AM
Replies: 8
Views: 1,187
Posted By ghalperin
Starter bench test spins slow

The starter on my 29 was spinning slow. 6 volt battery and all connections were fine. I installed my spare starter and everything is fine. Now I need to fix the slow starter. I disassembled the slow...
Forum: Model A (1928-31) 11-18-2018, 06:00 PM
Replies: 21
Views: 2,452
Posted By ghalperin
Re: Growling noise when clutch is engaged

That turned out to be the problem. I guess after my last 100 mile drive, my crankshaft endplay increased. I had one long starter bolt and it was hitting the flywheel. I guess that after swapping out...
Forum: Model A (1928-31) 11-18-2018, 01:23 PM
Replies: 21
Views: 2,452
Posted By ghalperin
Re: Growling noise when clutch is engaged

I just read that in Les Andrews book. Thatís easier than removing the transmission. Iíll report back when Iím done adjusting.
Forum: Model A (1928-31) 11-18-2018, 01:13 PM
Replies: 21
Views: 2,452
Posted By ghalperin
Re: Growling noise when clutch is engaged

I removed the spark plugs and had my son slowly hand crank. It looks like the outer part of the throw out bearing is hitting the fingers on the pressure plate. The housing part of the throw out...
Forum: Model A (1928-31) 11-18-2018, 10:16 AM
Replies: 21
Views: 2,452
Posted By ghalperin
Forum: Model A (1928-31) 11-17-2018, 12:50 PM
Replies: 21
Views: 2,452
Posted By ghalperin
Re: Growling noise when clutch is engaged

Iím going to do that this afternoon.
Forum: Model A (1928-31) 11-17-2018, 12:49 PM
Replies: 21
Views: 2,452
Posted By ghalperin
Re: Growling noise when clutch is engaged

The noise started suddenly and only happens when the clutch pedal is pushed. It ran for years without an issue.
Forum: Model A (1928-31) 11-16-2018, 10:49 PM
Replies: 21
Views: 2,452
Posted By ghalperin
Re: Growling noise when clutch is engaged

I read that .012 is the max.
Showing results 1 to 25 of 41

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:31 PM.