Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 77
Search took 0.01 seconds.
Search: Posts Made By: Gufshoz
Forum: Model A (1928-31) 01-25-2024, 12:35 PM
Replies: 13
Views: 1,007
Posted By Gufshoz
Re: Grinding

So this morning I put Castrol; Axel; GL-5; SAE 85W-140 into my transmission. After driving for a few miles and shifting quite a bit...the problem is solved. I went with nkaminar's suggestion for...
Forum: Model A (1928-31) 01-21-2024, 02:55 PM
Replies: 13
Views: 1,007
Posted By Gufshoz
Re: Grinding

Yup. Stock tranny.
Forum: Model A (1928-31) 01-21-2024, 12:50 PM
Replies: 13
Views: 1,007
Posted By Gufshoz
Grinding

I just finished changing all of the fluids after a 2000 mile trip in my A. No issues during the trip, but now I can't shift into 2nd and 3rd without severe grinding. I can get into all gears from a...
Forum: Model A (1928-31) 12-20-2023, 01:52 PM
Replies: 8
Views: 963
Posted By Gufshoz
Re: Another Horn Question

Thanks for the replies. I'm probably missing something basic. I believe that my horn is being grounded by the headlight bolt rather than the horn button completing the circuit. By using the paper...
Forum: Model A (1928-31) 12-18-2023, 05:37 PM
Replies: 8
Views: 963
Posted By Gufshoz
Another Horn Question

Hey everyone. I have an issue with a Spartan horn that was given to me by a friend. It works perfectly on my bench using the current 2 horn wires, but when I ground it to my A by mounting or just...
Forum: Model A (1928-31) 10-25-2023, 05:47 PM
Replies: 21
Views: 2,351
Posted By Gufshoz
Re: ...what is wrong with my sockets?

I have the same LED's and the same problem. They were great when I first installed them, but they started flickering on the low beams. When I removed them I noticed that the solder bumps; where...
Forum: Model A (1928-31) 09-18-2023, 09:06 PM
Replies: 15
Views: 1,203
Posted By Gufshoz
Re: knock during hard acceleration

These responses have really been educational for me. I had assumed that I would just be using the advance like I did with the stock head. I almost always ran about 2/3 to 3/4 advance. Now I’ll try...
Forum: Model A (1928-31) 09-17-2023, 06:06 PM
Replies: 15
Views: 1,203
Posted By Gufshoz
Re: knock during hard acceleration

Thanks guys. That was my first guess because I had never driven with the full advance. Full retard and she starts before she turn’s over completely then I normally keep the spark at about 2/3...
Forum: Model A (1928-31) 09-17-2023, 04:42 PM
Replies: 15
Views: 1,203
Posted By Gufshoz
knock during hard acceleration

Hey people,
I have 1,500 miles on a rebuild: cylinders sleeved, new babbitts, new Scat crank, tour ground cam, and a 5.5 Snyder head.
I did a 500 mi break-in drive, 100 mi/day, starting at 25 mph...
Forum: Model A (1928-31) 04-24-2023, 07:44 PM
Replies: 125
Views: 22,704
Posted By Gufshoz
Re: MMO in the Gas

I have always put 4 oz of MMO per 10 gal of gas when I fill up. I really don't know if I'm getting a benefit, but I don't really care and I'm not going to stop. It is part of my ritual of fueling...
Forum: Model A (1928-31) 01-25-2023, 11:08 AM
Replies: 52
Views: 7,995
Posted By Gufshoz
Re: How nat of you are using engine/motor pans?

I used to have issues with overheating. When I put the pans on I had problems with running too cold: thus, I now have a thermostat that keeps her at a nice 160 f.
Forum: Model A (1928-31) 01-08-2023, 09:10 PM
Replies: 5
Views: 1,138
Posted By Gufshoz
Re: Alignment of Focused Beam LED

I didn't measure mine, either. I used my garage door as my basic target, then took a drive. I had my wife (driving another vehicle) simulate an oncoming vehicle to check that I wasn't shining into...
Forum: Model A (1928-31) 02-25-2022, 11:51 AM
Replies: 8
Views: 1,211
Posted By Gufshoz
Re: valve guide

Since you're already planning on taking it to a machine shop, I would recommend having hardened valve seats installed. It's not too difficult to then to install modern guides and adjustable valves.
Forum: Model A (1928-31) 09-17-2021, 08:52 PM
Replies: 9
Views: 2,106
Posted By Gufshoz
Re: Rust Stains on Stainless Steel

I burnished my rusty bumpers and instrument panel with water-wetted aluminum foil. A little elbow grease and follow up waxing and you'll be amazed.
Forum: Model A (1928-31) 09-17-2021, 08:46 PM
Replies: 65
Views: 10,735
Posted By Gufshoz
Re: hoky fixs

When we removed the chicken wire/bondo to replace with welded patch panels, she looked like Swiss cheese.
Forum: Model A (1928-31) 09-17-2021, 08:44 PM
Replies: 48
Views: 10,215
Posted By Gufshoz
Re: Overheating 1930 Model A

Do you have engine pans? I had overheating issues and went back to the pans and a new 2-bladed fan. Then I had a problem getting her up to operating temp (she ran at about 120*), so I added a...
Forum: Model A (1928-31) 06-11-2021, 09:13 AM
Replies: 23
Views: 2,104
Posted By Gufshoz
Re: Jacking Instructions

I use a Sunex 2 ton "low rider" to raise mine. I cut grooves in the top of a hockey puck (which fits the top of my floor jack) to "embrace" the axle to keep it from sliding while I lift her. On...
Forum: Model A (1928-31) 06-02-2021, 06:05 PM
Replies: 10
Views: 1,194
Posted By Gufshoz
Natchez Trace

Next spring I plan on driving the Natchez Trace Parkway in my stock, 1930 coupe. I'm starting from the Alabama gulf coast and I'm trying to work out a timeline. I'd like to drive the actual parkway...
Forum: Model A (1928-31) 05-30-2021, 09:48 AM
Replies: 15
Views: 1,602
Posted By Gufshoz
Re: Starting issues when warm

katy- yes, it is a stock, ‘29.
Forum: Model A (1928-31) 05-28-2021, 10:04 PM
Replies: 15
Views: 1,602
Posted By Gufshoz
Re: Starting issues when warm

Thanks for the response, nkaminar and bobbader. I think I’ll go the route of exchanging for a rebuilt. With the summer cruising season upon us, I’d like to feel confident in my parts. We’re...
Forum: Model A (1928-31) 05-28-2021, 03:49 PM
Replies: 15
Views: 1,602
Posted By Gufshoz
Re: Starting issues when warm

A friend of mine has a spare starter and I put in my car, today. I had already replaced the ground strap and changed it’s position from a bolt on the bell housing to the proper hole on the frame and...
Forum: Model A (1928-31) 05-16-2021, 04:18 PM
Replies: 25
Views: 8,255
Posted By Gufshoz
Re: Intake & exhaust manifold torque

Could your muffler not have a passive fit on the manifold? I had trouble with mine seating and pulling open the #4 exhaust port.
Forum: Model A (1928-31) 05-16-2021, 04:09 PM
Replies: 10
Views: 1,262
Posted By Gufshoz
Re: Champagne

So, I filled the tank and it still was between 0-1/4; drove home, and the next day the gauge was working. We all have our gremlins, but mine just likes to mess with me.
I guess that the large...
Forum: Model A (1928-31) 05-14-2021, 08:19 PM
Replies: 10
Views: 1,262
Posted By Gufshoz
Champagne

A few months ago I started a thread about replacing my gas gauge float with a champagne cork. I am sad to say, but my A rejected the cork today. I wish I could find a beer cork so I could see if...
Forum: Model A (1928-31) 05-14-2021, 08:10 PM
Replies: 15
Views: 1,602
Posted By Gufshoz
Re: Starting issues when warm

700:
My engine has several thousand miles on it and compression of 55 lbs. in all cylinders, so I doubt if tight rings and pistons is the problem.
Thanks for the reply.
Showing results 1 to 25 of 77

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:35 AM.