Forum: Early V8 (1932-53)
06-16-2022, 12:03 PM
|
Replies: 20
Views: 1,526
|
Forum: Early V8 (1932-53)
06-16-2022, 09:41 AM
|
Replies: 20
Views: 1,526
Re: Torque tube noise
I am about to replace the pins in my 40 driveshaft....how do you flare the end of the pin so it will not back out?
|
Forum: Early V8 (1932-53)
06-10-2022, 03:47 PM
|
Replies: 16
Views: 1,885
Re: Clutch Plate Advice
Thank you!......also....I forgot to wedge the fingers in my pressure plate with wood when I removed it. Have I caused some kind of warpage now?
|
Forum: Early V8 (1932-53)
06-09-2022, 12:30 AM
|
Replies: 16
Views: 1,885
|
Forum: Early V8 (1932-53)
06-08-2022, 05:52 PM
|
Replies: 16
Views: 1,885
|
Forum: Early V8 (1932-53)
06-08-2022, 04:27 PM
|
Replies: 16
Views: 1,885
Clutch Plate Advice
Hello all,
I am in the process of replacing the clutch in my 40 Sedan. I purchased a NOS one from Ebay, manufactured by Perfection Gear Company (CF174). Are the old clutch plates a better choice...
|
Forum: Early V8
04-12-2021, 12:18 AM
|
Replies: 0
Views: 385
|
Forum: Early V8 (1932-53)
11-06-2015, 10:39 PM
|
Replies: 7
Views: 1,658
|
Forum: Early V8 (1932-53)
03-25-2015, 09:09 AM
|
Replies: 7
Views: 1,532
|
Forum: Early V8 (1932-53)
03-22-2015, 11:28 PM
|
Replies: 7
Views: 1,532
|
Forum: Early V8 (1932-53)
03-22-2015, 08:15 PM
|
Replies: 7
Views: 1,532
|
Forum: Early V8 (1932-53)
03-22-2015, 04:44 PM
|
Replies: 7
Views: 1,532
1939 Standard front crossmember question
Hello all,
I have not attempted to load photos yet, so I will explain this the best I can. I am in the process of replacing the front crossmember in my 39 Standard Coupe. At some point in time,...
|
Forum: Early V8
03-05-2014, 12:36 AM
|
Replies: 1
Views: 1,036
|
Forum: Early V8
03-03-2014, 02:48 PM
|
Replies: 1
Views: 1,036
39 swan shifter
Looking to buy a nice 39 swan shifter. Tower not needed.
Thanks in advance,
Sam
|
Forum: Early V8 (1932-53)
01-29-2014, 10:09 PM
|
Replies: 385
Views: 89,602
|
Forum: Early V8 (1932-53)
01-18-2014, 10:49 AM
|
Replies: 13
Views: 2,928
Re: lowering a 40 coupe
34PHAE.....how much did the front of your 40 drop with removing the wrap around spring? How did it effect the ride?
|
Forum: Early V8
01-14-2014, 10:27 PM
|
Replies: 4
Views: 1,277
|
Forum: Early V8
01-12-2014, 10:50 AM
|
Replies: 1
Views: 974
1939 wide five drums
Looking for a NICE set of front/rear wide five drums for my 39 coupe. Local pick up preferred. Thanks.
|
Forum: Early V8 (1932-53)
01-12-2014, 01:01 AM
|
Replies: 60
Views: 8,548
|
Forum: Early V8
12-16-2013, 10:01 PM
|
Replies: 3
Views: 1,137
|
Forum: Early V8
12-07-2013, 11:54 PM
|
Replies: 1
Views: 1,389
|
Forum: Early V8 (1932-53)
12-03-2013, 10:44 AM
|
Replies: 7
Views: 2,239
Re: Block cleaning
If you don't mind explaining...what type of tools/methods do you use to remove the sand in the block?
|
Forum: Early V8 (1932-53)
11-03-2013, 08:03 PM
|
Replies: 3
Views: 1,394
Re: wide 5 hubcaps 1936-1939
You were reading my mind! I was just looking at mine and could not figure out how I was going to get the stainless caps off to have tem restored. Thanks for the neat trick Kube!
|
Forum: Early V8
11-03-2013, 07:43 PM
|
Replies: 14
Views: 3,069
|
Forum: Early V8
10-16-2013, 08:01 PM
|
Replies: 3
Views: 1,618
|