Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 69
Search took 0.01 seconds.
Search: Posts Made By: fiddy6
Forum: Late V8 (1954+) Yesterday, 01:47 AM
Replies: 10
Views: 731
Posted By fiddy6
Re: Later distributor and a Holley 4000 - aka teapot

Another update.

I found and fixed more vacuum leaks. Several inlet manifold bolts were basically finger tight.

I managed to get to the point where I could Idle the engine right down with the...
Forum: Late V8 (1954+) 09-12-2020, 02:21 AM
Replies: 16
Views: 546
Posted By fiddy6
Re: Crank shaft flange

Exhaust manifold is from a passenger car by the look of it.

Rocker arms have ecg 6564 a2 which probably means the higher ratio.
Forum: Late V8 (1954+) 09-11-2020, 01:26 AM
Replies: 16
Views: 546
Posted By fiddy6
Re: Crank shaft flange

The crank pulley looks normal. As suspected looking under the valve cover yielded the ford number for all heads 6090.

The block casting number is above the oil filter.

The heads are ECZ-C... I...
Forum: Late V8 (1954+) 09-10-2020, 01:45 PM
Replies: 16
Views: 546
Posted By fiddy6
Re: Crank shaft flange

Im now intrigued as to where this motor came from the casting number is ECZ-6015-A. The valley cover has a road draft tube in it. It has a cover on the side of the block where I would expect it to...
Forum: Late V8 (1954+) 09-10-2020, 01:04 PM
Replies: 16
Views: 546
Posted By fiddy6
Re: Crank shaft flange

Trans is out soon. It leaks a bit too.

I think the rear main seal is leaking too.
Forum: Late V8 (1954+) 09-10-2020, 02:19 AM
Replies: 16
Views: 546
Posted By fiddy6
Crank shaft flange

Hi there,

I have a 56 ford victoria, M code, with what I thought was the original engine and transmission. I have a clanking noise at idle that goes away with revs and is not really audible...
Forum: Late V8 (1954+) 08-26-2020, 07:55 PM
Replies: 1
Views: 171
Posted By fiddy6
Holley 4000 Fuel inlet

Does anyone know the thread size or fitting name needed to fit into the brass inlet fitting on the back of the teapot?

Could it be a tapered fitting or a flare fitting?
Forum: Late V8 (1954+) 08-25-2020, 01:27 PM
Replies: 31
Views: 1,673
Posted By fiddy6
Re: Strange "Clanking Noise" at Idle

I was looking through the air inlet and outlet. I see the inspection plate now. Thank you.
Forum: Late V8 (1954+) 08-25-2020, 01:52 AM
Replies: 31
Views: 1,673
Posted By fiddy6
Re: Strange "Clanking Noise" at Idle

Is there any way to inspect these flywheel/flex plate rivets without pulling the transmission?

I think I have a similar sound at idle that goes away off idle.
Forum: Late V8 (1954+) 08-25-2020, 01:45 AM
Replies: 10
Views: 731
Posted By fiddy6
Forum: Late V8 (1954+) 08-25-2020, 01:38 AM
Replies: 10
Views: 731
Posted By fiddy6
Re: Later distributor and a Holley 4000 - aka teapot

Photo of the tool made to fix the plug surface
Forum: Late V8 (1954+) 08-25-2020, 01:05 AM
Replies: 10
Views: 731
Posted By fiddy6
Re: Later distributor and a Holley 4000 - aka teapot

Okay. I've finally gotten back to this. There is more to the saga. I found a fuel leak from the fuel inlet plug. The plug you remove to get to the back of the needle and seat. It was leaking down the...
Forum: Late V8 (1954+) 07-18-2020, 02:46 AM
Replies: 14
Views: 1,066
Posted By fiddy6
Re: Kultulz

Hope he's alright. I've really valued his knowledge.
Forum: Late V8 (1954+) 07-12-2020, 01:35 PM
Replies: 10
Views: 701
Posted By fiddy6
Re: 56 Victoria stock rear drums

I found some locally. Ajays in Waihi had some. Still pretty expensive. Thanks guys.
Forum: Late V8 (1954+) 07-08-2020, 04:06 AM
Replies: 10
Views: 701
Posted By fiddy6
Re: 56 Victoria stock rear drums

Thanks guys. I wanted to make sure they have me "over a barrel".

I might upgrade to a more common rear end in future but my car is basically stock except for a wiper motor and distributor. I'm...
Forum: Late V8 (1954+) 07-07-2020, 01:45 PM
Replies: 10
Views: 701
Posted By fiddy6
56 Victoria stock rear drums

I've been trying to source rear drums for a 56 Victoria with a stock rear end. Now I know MACs sell some but they are quite pricey and people I know have had quality issues with them in the past. ...
Forum: Late V8 (1954+) 06-02-2020, 01:51 PM
Replies: 10
Views: 731
Posted By fiddy6
Re: Later distributor and a Holley 4000 - aka teapot

HRR. Thanks. this is where I got the idea for the spark valve plug. I liked the method but didn't want to cut things I had no way to replace or plug easily.

Dmsfrr. Thanks I'll get a vacuum guage...
Forum: Late V8 (1954+) 06-02-2020, 01:32 AM
Replies: 10
Views: 731
Posted By fiddy6
Later distributor and a Holley 4000 - aka teapot

Hi All,

I thought I'd post my results of using a Holley 4000 Teapot with a 60's y block distributor.

Using a 3/8 UNF block off I have plugged the front vacuum port.
I have removed the spark...
Forum: Late V8 (1954+) 06-02-2020, 01:15 AM
Replies: 4
Views: 427
Posted By fiddy6
Re: 1956 rear quarter panels

I second EMS... I have used their rear inner and outer quarters... and their front quarters. Great product, fits well.
Forum: Late V8 (1954+) 12-15-2019, 01:02 AM
Replies: 24
Views: 1,567
Posted By fiddy6
Re: Interesting customized Falcon.

Thredbo

https://en.wikipedia.org/wiki/Thredbo,_New_South_Wales
Forum: Late V8 (1954+) 10-25-2019, 06:05 PM
Replies: 5
Views: 599
Posted By fiddy6
Re: 56 Victoria Wiper switch removal

Made a tool by hand with a file out of an old tiny socket. Works well. I got it out without scratching it up so I'm happy. Cheers for the advice.
Forum: Late V8 (1954+) 10-24-2019, 12:43 PM
Replies: 5
Views: 599
Posted By fiddy6
Re: 56 Victoria Wiper switch removal

Thanks. The tool looks essential. The seller of that particular one does not ship to the bottom of the world. I might have to make one from a socket.

Read your blog too. Newport wipers seem to be...
Forum: Late V8 (1954+) 10-24-2019, 12:35 AM
Replies: 5
Views: 599
Posted By fiddy6
56 Victoria Wiper switch removal

Hi,

I was wondering how to get the wiper switch out. I've removed the vacuum motor and now would like to get the switch out.

I'm going to order the newport kit and I'm wanting to take the old...
Forum: Late V8 (1954+) 08-27-2019, 01:40 AM
Replies: 7
Views: 655
Posted By fiddy6
Re: Unibody car on jack stands.

if in doubt, jack up the rear axle and front suspension. If I'm going to have my 56 up for long that's what I do... closest to how it sits on it wheels.
Forum: Late V8 (1954+) 06-11-2019, 03:37 PM
Replies: 9
Views: 737
Posted By fiddy6
Re: Fuel tank vent advice

The problem is access to where I need to drill the holes. I can't get the drill up into the space between inner quarter and the frame rail.

As with any body work on a car... the sheet metal work...
Showing results 1 to 25 of 69

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:46 PM.