Forum: Model A (1928-31)
04-13-2020, 09:05 PM
|
|
Replies: 1
Views: 1,138
'30 Header question. Not letting visor fit.
Hi. Sandollar here. Been away for some time.
Installed header on my '30 coupe. But when installing sun visor cannot get the 2 screw holes on post to line up.
The header sticks about 1/8"...
|
|
Forum: Model A (1928-31)
04-13-2020, 07:19 PM
|
|
Replies: 6
Views: 1,953
Re: top wood fitting
Hi. Sandollar here. Been away for some time. Installed header on my '30 coupe. But when installing sun visor cannot get the 2 screw holes on post to line up. Have Vol II Andrews book. The header...
|
|
Forum: Model A (1928-31)
03-23-2014, 12:32 PM
|
|
Replies: 8
Views: 6,657
|
|
Forum: Model A (1928-31)
03-18-2014, 02:12 PM
|
|
Replies: 8
Views: 6,657
Re: Clutch pedal adjustment
Hi from a beginner. Patrick- you say it is a matter of adjusting the clevis til you get 1 to 1.5 in. of free play. I have lifted the clutch arm and am not sure if am getting the right play. I saw...
|
|
Forum: Model A (1928-31)
05-23-2013, 10:54 AM
|
|
Replies: 8
Views: 7,284
|
|
Forum: Model A (1928-31)
04-23-2013, 02:09 PM
|
|
Replies: 6
Views: 1,347
|
|
Forum: Model A (1928-31)
04-23-2013, 02:08 PM
|
|
Replies: 6
Views: 1,347
Re: Wood Question for 30 Coupe
From my woodworking experience I know that linseed oil leaves a residual odor. The people that use it extensively use this formula:
Mix Linseed Oil and paint thinner 1 to 1 or 2 parts oil, 1 part...
|
|
Forum: Model A (1928-31)
04-22-2013, 10:47 PM
|
|
Replies: 49
Views: 9,993
|
|
Forum: Model A (1928-31)
04-22-2013, 09:40 PM
|
|
Replies: 6
Views: 1,347
Wood Question for 30 Coupe
Hi Everyone. Kinda new to the board so have newbie question.
Side window wood is old but still useable. Looked painted.
Is it acceptable to paint all my wood for protection? After all it will...
|
|
Forum: Model A (1928-31)
03-22-2013, 10:32 AM
|
|
Replies: 30
Views: 7,226
Re: Easy way to paint wheels ?
Has anyone used Dunn-Edwards Syn-Lustro paint? It is for metal and dries harder than Rust o leum. Does not come in spray cans however.
|
|
Forum: Model A (1928-31)
12-09-2012, 12:35 PM
|
|
Replies: 2
Views: 1,666
Re: Need sheet metal man in Arizona
Sorry for the delay in answering. I am in Tempe.. But I get up your way very often since I have a place in Strawberry.
I am Ernie Sandoval cell # 480-510-7169.
We should connect.
|
|
Forum: Model A (1928-31)
10-01-2012, 04:47 PM
|
|
Replies: 2
Views: 1,666
Need sheet metal man in Arizona
I am close to needing sheet metal work done for my 30 Deluxe coupe. Does not need too much done. Does anyone know a good sheet metal man in Arizona? Phoenix area is preferred but I will travel if...
|
