Forum: Early V8
01-16-2024, 05:35 PM
|
Replies: 0
Views: 256
|
Forum: Early V8
02-16-2021, 04:29 PM
|
Replies: 0
Views: 330
1939 V8 piston set (0.060)
Looking for a set of 0.060 oversized pistons and rings for a 1939 221 cubic inch V8, 24-stud engine build.
|
Forum: Early V8
10-06-2020, 02:07 PM
|
Replies: 0
Views: 438
Canadian C91A-7129 Thrust Washer
Looking for a Canadian-only thrust washer for 3-speed Ford cluster gear. It is different than the standard bow-tie.
https://live.staticflickr.com/65535/50428665517_462c0003af.jpg...
|
Forum: Early V8 (1932-53)
10-05-2020, 08:23 PM
|
Replies: 9
Views: 1,350
|
Forum: Early V8 (1932-53)
10-05-2020, 07:53 PM
|
Replies: 9
Views: 1,350
|
Forum: Early V8 (1932-53)
10-05-2020, 07:16 PM
|
Replies: 9
Views: 1,350
Cluster Gear Identification
I am building a 1939 Ford transmission and bought a gear set from a friend. However, when I started to look at the cluster gear end I noticed it was different than the typical 28-24-18-14 gear set....
|
Forum: Model A (1928-31)
09-21-2020, 10:40 AM
|
Replies: 9
Views: 3,770
Disassemble Tudor Body
I am in the process of restoring a 1929 Ford Model A Tudor and I am working on repairing the body. It is very rusty with some original paint on it. I have started the exterior stripping of it with a...
|
Forum: Model A (1928-31)
09-11-2020, 08:31 PM
|
Replies: 8
Views: 1,038
Body Cart for Tudor Body
I need to build a body cart for my 1929 Ford Tudor body and I need advice on the dimensions. I am using 2x4 and 4x4 for the frame, but not sure how big I should make it. Anyone lend some advice on a...
|
Forum: Early V8
06-10-2020, 09:00 PM
|
Replies: 0
Views: 896
|
Forum: Early V8 (1932-53)
06-07-2020, 08:39 PM
|
Replies: 20
Views: 3,483
Re: Transmisson Gear Set Interchange
Yeah I decided to pass on them, as the one I needed had a pretty chewed up gear set. If anyone is near Calgary, Alberta, Canada might be a good deal.
|
Forum: Early V8 (1932-53)
06-04-2020, 09:50 AM
|
Replies: 20
Views: 3,483
Re: Transmisson Gear Set Interchange
Here are the transmissions.
https://live.staticflickr.com/65535/49970748037_f0d49c468e_c.jpg (https://flic.kr/p/2j8K9rk)
https://live.staticflickr.com/65535/49970479876_f5e6b4e14a_c.jpg...
|
Forum: Early V8 (1932-53)
06-03-2020, 11:46 PM
|
Replies: 20
Views: 3,483
Re: Transmisson Gear Set Interchange
Well I don’t have a shifter yet, so that is not a big deal yet. As for the three transmissions i think there is one I can use, and the others might help offset the costs of the package.
|
Forum: Early V8 (1932-53)
06-03-2020, 11:07 PM
|
Replies: 20
Views: 3,483
Re: Transmisson Gear Set Interchange
Well I think I got lucky today and found someone who has three transmissions for 40 bucks. Think that is a hell of a deal too.
Looks like one of the transmissions has a Borg Warner R10 overdrive...
|
Forum: Early V8 (1932-53)
06-03-2020, 01:21 PM
|
Replies: 20
Views: 3,483
|
Forum: Early V8 (1932-53)
06-03-2020, 01:06 PM
|
Replies: 20
Views: 3,483
Transmisson Gear Set Interchange
So I have started the teardown of the 78-casting, three-speed transmission I acquired and found that at some point in its past it had an earlier ('32-35) gear set installed in it. What gear sets from...
|
Forum: Early V8 (1932-53)
06-01-2020, 11:06 PM
|
Replies: 8
Views: 1,246
Re: Universal Joint Removal
Little heat and she popped right off. For the clutch shaft removal, do you grind off the clutch fork pin and slide the shaft out?
|
Forum: Early V8 (1932-53)
06-01-2020, 09:26 PM
|
Replies: 8
Views: 1,246
|
Forum: Early V8 (1932-53)
06-01-2020, 09:18 PM
|
Replies: 8
Views: 1,246
Universal Joint Removal
So I just started taking apart my three-speed Ford toploader transmission and I cannot figure out, for the life of me, how to remove the universal joint from the back of the transmission. Can anyone...
|
Forum: Early V8 (1932-53)
02-09-2020, 03:28 PM
|
Replies: 6
Views: 1,609
Re: Using later valves in a '39 flathead
Thanks guys for this. I am relatively new here, but somewhat of a regular on the HAMB forum. Thanks for the info, rather new to the flathead, but have worked on a few over the years.
|
Forum: Early V8 (1932-53)
02-09-2020, 12:14 AM
|
Replies: 6
Views: 1,609
Using later valves in a '39 flathead
Just wondering if you can use the later 8BA style valves and guides in the earlier flathead blocks? I have a bunch of valves, but not many guides. Seems the later valve and guides are cheaper than...
|