Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 10 of 10
Search took 0.00 seconds.
Search: Posts Made By: mike cox
Forum: Early V8 (1932-53) 03-10-2019, 08:56 AM
Replies: 18
Views: 1,415
Posted By mike cox
pinion deph shims

Hello,would like to know what shims are to be used to set the pinion deph on a, 1947, also where would one buy such shims. Thank you for your help. Mike
Forum: Early V8 (1932-53) 03-28-2017, 10:38 AM
Replies: 18
Views: 1,806
Posted By mike cox
Re: 1946 - 1948 ford Aluminum parts

Have 46-48 heater , that the outside box covering the inter box is aluminum. Mike
Forum: Early V8 (1932-53) 11-04-2016, 08:09 PM
Replies: 6
Views: 1,184
Posted By mike cox
Re: Bumper gaurd ID?

Hi, guards are after market for 47-48,there is a, bar that goes between the guards.They are for the front,the late Bob McCoppin, did a, article in the V-8 times back in the 90's on the difference...
Forum: Early V8 (1932-53) 08-14-2016, 05:32 PM
Replies: 4
Views: 937
Posted By mike cox
pre fit and alignment

47 sedan-coup is ready for paint,have the bare body on a cart and plan to paint it on the cart. Will pre fit all sheet metal,doors,hood and trunk for proper alignment, and paint them off the body. My...
Forum: Early V8 (1932-53) 12-09-2015, 07:25 PM
Replies: 0
Views: 796
Posted By mike cox
81A-7061- main shaft spec

Hi,have done a search on this site, Vanpelt's, and looked in the Ford Chassis and part's catalogue and can't find any spec for the 81A-7061, main shaft .Can someone tell me what the original spec...
Forum: Early V8 (1932-53) 11-29-2015, 08:59 PM
Replies: 11
Views: 1,330
Posted By mike cox
Re: 1947 transmission trouble

Thank ,you all again for the help and ideas,on the transmission.Will get Van Pelt's book and then take the transmission out of the car and start over. Also the car came with some extra transmission...
Forum: Early V8 (1932-53) 11-28-2015, 05:11 PM
Replies: 11
Views: 1,330
Posted By mike cox
Re: 1947 transmission trouble

Terry,thanks for the reply,will wait until the car is under it's own power and see if shift's,through the gears. Mike
Forum: Early V8 (1932-53) 11-28-2015, 03:23 PM
Replies: 11
Views: 1,330
Posted By mike cox
1947 transmission trouble

Hi,am restoring a 47 and have the body off the frame.The engine and drive train are in the frame. Problem with the transmission is when the shift rods are hooked up (or not hooked up) can't shift...
Forum: Early V8 06-02-2013, 05:04 AM
Replies: 10
Views: 1,602
Posted By mike cox
Re: 42-48 front bumper tips

Hello, will buy your bumper tips , just want to make sure we are talking about 4,tips with no dents. Thank you. Mike,
Forum: Early V8 (1932-53) 10-20-2010, 08:57 PM
Replies: 1
Views: 899
Posted By mike cox
8 ba rod bearings

Hello, have a,question that I, would like to know the answer to. Have a, set of nos 8BA rod bearings (FORD OF CANADA) they have no oil hole,also set of clevite bearings with 1, oil hole and a, set of...
Showing results 1 to 10 of 10

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:15 PM.