Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: russcc
Forum: Early V8 (1932-53) Yesterday, 05:44 PM
Replies: 5
Views: 263
Posted By russcc
Re: 34 crankshaft nut wrench size

Tough place to measure across the flats on what looks like a 1 3/8" hex bolt head unless you have pair of calipers.
Forum: Early V8 (1932-53) Yesterday, 05:42 PM
Replies: 3
Views: 166
Posted By russcc
Re: ID aftermarket drums 21A/O1A-1125

The Early V8 store and Joe's both sell the drums, with the 21A & 01A ones having a 3 1/4" id mounting hole where the hub fits under the drum. I also see Bolling Bros. drum that look similar.
Forum: Early V8 (1932-53) Yesterday, 05:31 PM
Replies: 18
Views: 542
Posted By russcc
Re: Cast iron surface rust removal

Thank you for the acid suggestion. Cut it, and sprayed it on the cast parts and did a good job of cleaning the surface rust off. Washed them off, and dunked them in a bath pf backing soda and water,...
Forum: Early V8 (1932-53) Yesterday, 08:59 AM
Replies: 3
Views: 166
Posted By russcc
ID aftermarket drums 21A/O1A-1125

I have set of aftermarket drums that I would like to identify the Mfg. and aprox age of them. The casting has MB on it along with the #41, and some other numbers. The box was marked 21A-1125. Photos....
Forum: Early V8 (1932-53) Yesterday, 08:54 AM
Replies: 8
Views: 399
Posted By russcc
Re: Identifying an oil pan

Thank you all for the heads up.
Forum: Early V8 04-16-2021, 06:13 PM
Replies: 0
Views: 50
Posted By russcc
37-48 Sector, (worm steering) gear

Very good used 78-78-3575 sector gear, '37-48, and F1 steering boxes. The shaft has no measurable wear over it's length, including the seal area. Measures 1.122 OD over it's length. The worm gear...
Forum: Early V8 (1932-53) 04-16-2021, 11:24 AM
Replies: 8
Views: 399
Posted By russcc
Re: Identifying an oil pan

Here is photo of the inside. This pan is listed in bible as a 59A-6675, '32-48. It has the vent, but no provision for an oil filter return line with the dip stick tube boss.
Forum: Early V8 (1932-53) 04-16-2021, 11:07 AM
Replies: 18
Views: 542
Posted By russcc
Re: Cast iron surface rust removal

Thank you all. Some of these parts are NOS brake drums, exhaust manifolds and cylinder heads so spraying and neutralizing would be the best solution for these large bulky items.
Forum: Early V8 04-16-2021, 08:03 AM
Replies: 0
Views: 106
Posted By russcc
Original Lincoln Zephyr 26 Tooth gear set

Complete, original Lincoln Zephyr 26T gear set. 18T main drive, 26t cluster, 24T second gear. All the gears are in good to excellent condition. These are not repops, they are all original OEM,...
Forum: Early V8 (1932-53) 04-16-2021, 07:49 AM
Replies: 18
Views: 542
Posted By russcc
Cast iron surface rust removal

I have several NOS cast iron parts with some very light surface rust on them in places. Is there a solution that could be applied, and rinsed off that would remove most of the light rust to save some...
Forum: Early V8 (1932-53) 04-16-2021, 07:45 AM
Replies: 3
Views: 252
Posted By russcc
Re: United oil bath air cleaner.

Yes, is United Air Cleaner manufacturers name on the air cleaner itself ? Unable to identify the mfg. Thank you.
Forum: Early V8 (1932-53) 04-16-2021, 07:43 AM
Replies: 8
Views: 399
Posted By russcc
Re: Identifying an oil pan

Yes, there is a vent in the front. I will post a photo of the inside.
Forum: Early V8 (1932-53) 04-15-2021, 06:16 PM
Replies: 8
Views: 399
Posted By russcc
Identifying an oil pan

In looking at this oil pan, It does not seem to resemble a 59AB pan, especially the location of the drain plug off center. From the inside it looks similar to 59AB. Any ideas ? Thank you. Photo;
Forum: Early V8 (1932-53) 04-15-2021, 06:11 PM
Replies: 3
Views: 252
Posted By russcc
United oil bath air cleaner.

I read the EV8 Time article on the the United Oil Bath Air cleaner, and looked at the one I had see if it said United Air Cleaner Co. on it, but could not locate anything. It did have the "Caution"...
Forum: Early V8 (1932-53) 04-15-2021, 06:03 PM
Replies: 16
Views: 771
Posted By russcc
Re: 39 lincoln zephyr

I believe AACA has a Licncoln forum where you might be able to check prices. That maroon 4 door was a beauty, and darn slick for a fordor.
Forum: Early V8 (1932-53) 04-13-2021, 05:46 PM
Replies: 2
Views: 289
Posted By russcc
Welding early aluminum heads

I friend of mine, an excellent TIG welder, told me than the older cast aluminum can be difficult to weld. Anyone have any experience welding the early heads. The ones I may want to weld are '33, 34,...
Forum: Early V8 (1932-53) 04-13-2021, 05:33 PM
Replies: 14
Views: 852
Posted By russcc
Re: Help identifying EV8 parts

That's what the tag on it said '36, but wanted to confirm. Thank you all.
Forum: Early V8 04-12-2021, 10:29 AM
Replies: 0
Views: 110
Posted By russcc
Lincoln V-12 parts

Late 30's - early '40's Lincoln V-12 parts. All prices, plus shipping.

1. Left & right exhaust manifolds, good condition used, $175. pair
2. 3 Spark plug wire conduits, either NOS or excellent...
Forum: Early V8 (1932-53) 04-11-2021, 05:47 PM
Replies: 10
Views: 524
Posted By russcc
Re: Day out in the 33

That was a great article in the recent V8 times, thank you. Interesting to hear about the torque from the 4" crank pulling the hills.
Forum: Early V8 (1932-53) 04-10-2021, 06:34 PM
Replies: 6
Views: 501
Posted By russcc
Re: Shackle pin, heads up

I have never seen any shackles plated either. They were stamped Ford USA, and came from 3rd gen, and I was happy to get the original type. I would have posted a picture, but they were already...
Forum: Early V8 (1932-53) 04-10-2021, 06:24 PM
Replies: 7
Views: 360
Posted By russcc
Re: Question about 32-34 spindles

Thank you. That's it, they are not stock.
Forum: Early V8 (1932-53) 04-10-2021, 12:54 PM
Replies: 7
Views: 360
Posted By russcc
Question about 32-34 spindles

What is the purpose of the heavy bars attached to the kingpins in the '32-34 spindles in the photo. Thank you.
Forum: Early V8 (1932-53) 04-10-2021, 12:52 PM
Replies: 14
Views: 852
Posted By russcc
Re: Help identifying EV8 parts

Thank you all. I believe the one on the far right is 1936. How about that long legged one on the far left ? Any ideas.
Forum: Early V8 04-09-2021, 01:41 PM
Replies: 0
Views: 101
Posted By russcc
New Manley 8BA type flathead valves

Set of 8 new Manley Performance custom stainless valves for the flathead. These valves are special order, with head diameter of 1.600, stem OD of .240, OAL 4.836. The stem has the standard Ford...
Forum: Early V8 04-09-2021, 09:44 AM
Replies: 0
Views: 110
Posted By russcc
Pair of 32-34 spindles

Pair of '32-34 LH & RH spindles, B-3105 & B-3106. These appear to be NOS, but not sure about the kings pins. $225. for the pair, plus shipping.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:19 AM.