Forum: Early V8 (1932-53)
07-16-2019, 03:28 PM
|
Replies: 10
Views: 2,436
Re: Help with Engine dating
Your engine also appears to have a factory relief, as does mine, which has the 59 casting number on the bell housing.
ckh
|
Forum: Early V8 (1932-53)
07-11-2019, 11:00 PM
|
Replies: 7
Views: 1,880
Re: 32 Driveshaft and Torque Tube Lengths???
Dale,
If you haven't already done so, read this thread.(https://www.fordbarn.com/forum/showthread.php?t=233411) paying special
attention to the reply by John R. Little more difficult to...
|
Forum: Early V8 (1932-53)
01-21-2019, 11:32 PM
|
Replies: 33
Views: 6,045
|
Forum: Early V8 (1932-53)
01-21-2019, 06:14 PM
|
Replies: 33
Views: 6,045
|
Forum: Early V8 (1932-53)
06-20-2018, 12:33 PM
|
Replies: 2
Views: 1,297
|
Forum: Early V8 (1932-53)
06-14-2018, 03:54 PM
|
Replies: 17
Views: 2,861
Re: Widened wheels
TJ is right. 49-53 F1 pickups had an optional wheel that was 16x5. Mercury had a 16x5 also. 1941 I think. Beware of those who say they can install your
centers in an outer rim that will fit. ...
|
Forum: Early V8 (1932-53)
05-10-2018, 01:46 PM
|
Replies: 10
Views: 2,429
|
Forum: Early V8 (1932-53)
02-08-2018, 01:33 PM
|
Replies: 2
Views: 903
|
Forum: Early V8 (1932-53)
10-13-2016, 06:08 PM
|
Replies: 2
Views: 1,336
Advice needed on flanged full floating bearings
From what I can tell these bearings were offered in these different types:
Nickel cadmium, Tin base babbitt, Lead base babbitt, and copper lead base.
Is there a preference as to which type to use...
|
Forum: Early V8 (1932-53)
07-26-2016, 03:58 PM
|
Replies: 21
Views: 8,782
|
Forum: Early V8 (1932-53)
06-05-2016, 06:03 PM
|
Replies: 11
Views: 2,990
Re: Rear main seal '32-'38?
I'm no expert, but maybe this will help. On my 35/early 36 engine with babbit main bearings, the upper part of the seal, which I believe is made of some type of alloy, is pressed into the block by...
|
Forum: Early V8 (1932-53)
01-31-2015, 10:57 AM
|
Replies: 7
Views: 2,135
|
Forum: Early V8 (1932-53)
06-07-2014, 12:16 PM
|
Replies: 12
Views: 2,625
|
Forum: Early V8 (1932-53)
06-07-2014, 11:13 AM
|
Replies: 12
Views: 2,625
Re: Torque tube dimension
Thanks 42merc for your help. Wish I could find some literature with pictures, dimensions etc. of all the rear ends 28/48 and what will interchange as well as mix and match. The green book is...
|
Forum: Early V8 (1932-53)
06-06-2014, 03:40 PM
|
Replies: 12
Views: 2,625
Torque tube dimension
Does anyone happen to know the correct total length of a late 32 torque tube with hexagon flange?
Thanks
|
Forum: Early V8 (1932-53)
11-29-2013, 08:40 PM
|
Replies: 177
Views: 72,817
|
Forum: Model-A
10-24-2013, 01:52 PM
|
Replies: 0
Views: 785
Shim pack wanted
I need a main bearing shim pack. Federal-Mogul #1508 M 1/64
Any leads would be appreciated.
Thanks
|
Forum: Early V8
10-24-2013, 01:46 PM
|
Replies: 0
Views: 868
Shim pack wanted
I need a main bearing shim pack . Federal-Mogul #1508 M 1/64
Any leads would be appreciated.
Thanks
|