Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 18 of 18
Search took 0.00 seconds.
Search: Posts Made By: ckh
Forum: Early V8 (1932-53) 07-16-2019, 03:28 PM
Replies: 10
Views: 1,608
Posted By ckh
Re: Help with Engine dating

Your engine also appears to have a factory relief, as does mine, which has the 59 casting number on the bell housing.
ckh
Forum: Early V8 (1932-53) 07-11-2019, 11:00 PM
Replies: 7
Views: 811
Posted By ckh
Re: 32 Driveshaft and Torque Tube Lengths???

Dale,
If you haven't already done so, read this thread.(https://www.fordbarn.com/forum/showthread.php?t=233411) paying special
attention to the reply by John R. Little more difficult to...
Forum: Early V8 (1932-53) 01-21-2019, 11:32 PM
Replies: 25
Views: 2,820
Posted By ckh
Re: 1932 dual guage

Thanks. Do you happen to have his contact info?
Forum: Early V8 (1932-53) 01-21-2019, 06:14 PM
Replies: 25
Views: 2,820
Posted By ckh
Re: 1932 dual guage

Does anyone make/sell new faces for the 32 dual gauge?
Forum: Early V8 (1932-53) 06-20-2018, 12:33 PM
Replies: 2
Views: 623
Posted By ckh
Re: 32 Grill Shell

Just under 1 inch. .930-.940
Forum: Early V8 (1932-53) 06-14-2018, 03:54 PM
Replies: 17
Views: 2,020
Posted By ckh
Re: Widened wheels

TJ is right. 49-53 F1 pickups had an optional wheel that was 16x5. Mercury had a 16x5 also. 1941 I think. Beware of those who say they can install your
centers in an outer rim that will fit. ...
Forum: Early V8 (1932-53) 05-10-2018, 01:46 PM
Replies: 10
Views: 1,720
Posted By ckh
Forum: Early V8 (1932-53) 02-08-2018, 01:33 PM
Replies: 2
Views: 678
Posted By ckh
Re: Steve Clark - Utah

Steve Clark 801 592-0312
Forum: Early V8 (1932-53) 10-13-2016, 06:08 PM
Replies: 2
Views: 858
Posted By ckh
Advice needed on flanged full floating bearings

From what I can tell these bearings were offered in these different types:
Nickel cadmium, Tin base babbitt, Lead base babbitt, and copper lead base.
Is there a preference as to which type to use...
Forum: Early V8 (1932-53) 07-26-2016, 03:58 PM
Replies: 21
Views: 3,884
Posted By ckh
Re: About oil pressure relief springs- Again

Try All Ford Parts in Campbell, Ca for the springs.

1-800-532-1932
Forum: Early V8 (1932-53) 06-05-2016, 06:03 PM
Replies: 11
Views: 1,315
Posted By ckh
Re: Rear main seal '32-'38?

I'm no expert, but maybe this will help. On my 35/early 36 engine with babbit main bearings, the upper part of the seal, which I believe is made of some type of alloy, is pressed into the block by...
Forum: Early V8 (1932-53) 01-31-2015, 10:57 AM
Replies: 7
Views: 1,670
Posted By ckh
Re: Who here does the manual to hydraulic pedal conversion, on the original pedal ass

Richard Lacy / Early V8 Garage.
1217 Azusa Canyon Road
West Covina,CA91790
(626)338-2282
Forum: Early V8 (1932-53) 06-07-2014, 12:16 PM
Replies: 12
Views: 2,147
Posted By ckh
Re: Torque tube dimension

Andy,
The early 32 dimension is different than the 33-34.
Forum: Early V8 (1932-53) 06-07-2014, 11:13 AM
Replies: 12
Views: 2,147
Posted By ckh
Re: Torque tube dimension

Thanks 42merc for your help. Wish I could find some literature with pictures, dimensions etc. of all the rear ends 28/48 and what will interchange as well as mix and match. The green book is...
Forum: Early V8 (1932-53) 06-06-2014, 03:40 PM
Replies: 12
Views: 2,147
Posted By ckh
Torque tube dimension

Does anyone happen to know the correct total length of a late 32 torque tube with hexagon flange?

Thanks
Forum: Early V8 (1932-53) 11-29-2013, 08:40 PM
Replies: 152
Views: 51,169
Posted By ckh
Re: 1932 Ford Deluxe 3W, Murray Body # informal registry, how many are still around?

My 3 window is #B520B-5714. It's a rumble seat car with late sun visors. As far as I can tell it was manufactured in July of '32. A friend down the street has an original 3 window also but the body...
Forum: Model-A 10-24-2013, 01:52 PM
Replies: 0
Views: 466
Posted By ckh
Shim pack wanted

I need a main bearing shim pack. Federal-Mogul #1508 M 1/64
Any leads would be appreciated.
Thanks
Forum: Early V8 10-24-2013, 01:46 PM
Replies: 0
Views: 438
Posted By ckh
Shim pack wanted

I need a main bearing shim pack . Federal-Mogul #1508 M 1/64
Any leads would be appreciated.
Thanks
Showing results 1 to 18 of 18

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:16 AM.