Forum: Early V8 (1932-53)
02-13-2024, 10:43 AM
|
Replies: 20
Views: 1,079
|
Forum: Early V8 (1932-53)
01-26-2024, 03:23 PM
|
Replies: 43
Views: 1,872
Re: 35/36 Pickup Seat Base
Hello,
Here is my '36 Ford pickup hardwood seat base I purchased years ago from Lebaron-Bonney.
I know dimensionally it does not help you, but nice to look at though.
Bruce in California
|
Forum: Early V8 (1932-53)
01-25-2024, 04:13 PM
|
Replies: 18
Views: 1,063
Re: Muffler help
Hello,
More photos....I had installed all new exhaust system from exhaust manifolds on back, to tip of tailpipe.
Bruce in Ca.
|
Forum: Early V8 (1932-53)
01-25-2024, 04:04 PM
|
Replies: 18
Views: 1,063
Re: Muffler help
Hello,
My '36 Ford pickup new Muffler from Waldron's fit perfectly (no cutting of frame required).
SORRY, I do not remember the Inlet and Outlet orientations.
Bruce in Ca.
|
Forum: Early V8 (1932-53)
01-19-2024, 12:32 PM
|
Replies: 9
Views: 657
Re: 1936 ford pickup battery tray
Hello,
I have a '36 Ford pickup and bought the two pieces that hold the Battery from Wescott's in Oregon.
I hope these photos help some.
Bruce in California
|
Forum: Early V8 (1932-53)
01-05-2024, 10:18 AM
|
Replies: 10
Views: 758
|
Forum: Early V8 (1932-53)
01-05-2024, 10:12 AM
|
Replies: 10
Views: 758
|
Forum: Early V8 (1932-53)
11-02-2023, 01:14 PM
|
Replies: 16
Views: 1,241
Re: Bolt buster /induction heater
Hello to all....I bought the Bolt Buster 1800 and it worked perfectly to remove all 48 hex nuts from the flatheads. It did quit working once (I "think" I got it overheated, because they state 2...
|
Forum: Early V8 (1932-53)
10-27-2023, 02:50 PM
|
Replies: 2
Views: 421
|
Forum: Early V8 (1932-53)
10-27-2023, 02:19 PM
|
Replies: 2
Views: 421
NPT Thread Size needed....
I have the 59A/B cast iron heads and need to know the NPT Thread Size where the water temperature sending unit screws into.
THANK YOU,
Bruce in Ca.
|
Forum: Early V8
10-19-2023, 05:07 PM
|
Replies: 0
Views: 355
|
Forum: Early V8
10-13-2023, 03:33 PM
|
Replies: 1
Views: 628
|
Forum: Early V8 (1932-53)
10-03-2023, 11:38 AM
|
Replies: 29
Views: 1,819
Re: Update on 60HP engine project
Hello Lawson Cox....You did a wonderful job with the V8 60 HP Engine, Transmission and Stand....Congratulations on a very nice display....
Bruce in California.
|
Forum: Early V8 (1932-53)
09-08-2023, 04:36 PM
|
Replies: 29
Views: 1,768
Re: Early 1946 Ford 5W Coupe Start
Thank you tubman,
I have a 1936 Simplex Servi Cycle with maqneto and get no spark from the spark plugs. Proper gap is set for plugs and points at 0.020". To get to the condenser, points and coils...
|
Forum: Early V8 (1932-53)
09-08-2023, 12:49 PM
|
Replies: 29
Views: 1,768
Re: Early 1946 Ford 5W Coupe Start
Hello Tubman,
Because as mentioned above that you are the resident expert on Condensers.
I have a question, how do you test a condenser to check if it is good or bad.
Bruce in Ca.
|
Forum: Early V8 (1932-53)
08-30-2023, 10:09 AM
|
Replies: 34
Views: 3,175
Re: The cylinder head replacement story begins…
Hello SoCalCoupe,
As Tim Ayers mentioned above about the NAVARRO heads, I had Purchased a set from H&H because they do use the stock studs. My Block is a '46 - '48 with 3 3/16 bore. I used the...
|
Forum: Early V8 (1932-53)
08-23-2023, 09:15 AM
|
Replies: 11
Views: 900
Re: Cast Iron Heads....
Hello to all here on Ford Barn,
My current situation for my '36 Ford pickup regarding heads is as follows....
I blew a head gasket so removed both heads and had magna fluxed only to find cracks...
|
Forum: Early V8 (1932-53)
08-23-2023, 08:55 AM
|
Replies: 11
Views: 900
Re: Cast Iron Heads....
Hello 38 coupe,
I agree with you that they look kinda funny when mixed.
The cast iron heads on my '46 - '48 engine were 59A/B on drivers side and 81A-6050 on Passenger side. I blew a head gasket...
|
Forum: Early V8 (1932-53)
08-23-2023, 08:52 AM
|
Replies: 11
Views: 900
Re: Cast Iron Heads....
Hello Flatmotors,
Thank you for your reply. Can you send several photos of the heads top and bottom side and let me know how much you want for them. You can email to me at ...
|
Forum: Early V8 (1932-53)
08-17-2023, 04:19 PM
|
Replies: 11
Views: 900
|
Forum: Early V8 (1932-53)
08-17-2023, 03:45 PM
|
Replies: 11
Views: 900
Cast Iron Heads....
Hello,
I have a '46-'48 block and need to know which are the correct cast iron heads for it.
Cast iron heads that came on it were 59A/B on one side and 81A on other side.
Please let me know...
|
Forum: Early V8
08-17-2023, 03:36 PM
|
Replies: 1
Views: 628
|
Forum: Early V8 (1932-53)
04-14-2023, 01:40 PM
|
Replies: 52
Views: 5,203
Re: 1938 V8 head removal
Hello BlueSpark,
Thank you for your photos and comments along the way.
I too have a '36 Ford pickup with a later '46-'48 engine and am going through basically the same thing as you. Due to blown...
|
Forum: Early V8 (1932-53)
01-11-2023, 05:58 PM
|
Replies: 12
Views: 1,597
|
Forum: Early V8 (1932-53)
01-11-2023, 04:35 PM
|
Replies: 12
Views: 1,597
|