Forum: Early V8 (1932-53)
08-12-2023, 12:22 PM
|
Replies: 15
Views: 668
|
Forum: Early V8 (1932-53)
08-06-2023, 03:04 AM
|
Replies: 13
Views: 1,522
Re: hard start only when hot
Hi all,
i had the same issue on my 37 when i bought it. when was hot if i stop the engine i was obliged to pump several time with accelerator to run... I measured temp at fuel pum and carb and found...
|
Forum: Early V8 (1932-53)
06-28-2022, 04:42 PM
|
Replies: 7
Views: 644
Re: Vapor lock...😵www.jalopyjournal.net💫
Hi guys,
i solved my vapor lock problems with installing little steel sheet to close the exhaust pipe going thru the intake manifold. did this last year, and i never had any more vapor lock!
|
Forum: Early V8 (1932-53)
12-28-2021, 03:57 AM
|
Replies: 5
Views: 799
|
Forum: Early V8 (1932-53)
12-28-2021, 03:21 AM
|
Replies: 137
Views: 21,400
Re: 1939’ Deluxe 2DR Sedan
Very nice car!
I made myself the new harness on my 37 tudor but the only wire i haven't changed is the dome light wire :).
|
Forum: Early V8 (1932-53)
10-14-2021, 09:27 AM
|
Replies: 15
Views: 1,754
|
Forum: Early V8 (1932-53)
10-13-2021, 09:36 AM
|
Replies: 15
Views: 1,754
|
Forum: Early V8 (1932-53)
10-09-2021, 05:16 AM
|
Replies: 20
Views: 2,159
|
Forum: Early V8 (1932-53)
10-09-2021, 05:14 AM
|
Replies: 20
Views: 2,159
|
Forum: Early V8 (1932-53)
10-08-2021, 12:09 PM
|
Replies: 71
Views: 8,126
Re: Help I’m Lost
i think the first thing to do is to clean the gas pum, put a gas filter before it, see if gas comes out when you start. if all is good, put a wire between + and coil and test to start.
like deuce...
|
Forum: Early V8 (1932-53)
10-08-2021, 07:48 AM
|
Replies: 6
Views: 667
|
Forum: Early V8 (1932-53)
08-16-2021, 04:59 AM
|
Replies: 15
Views: 1,997
Re: My 1941 Ford isn't running right
Hi guys,
I had almost the same issue on my 37 tudor. It was idling but not climbing in turns. changed the condenser and all was OK. i opened it to see and you can see the pictures...
on chinese...
|
Forum: Early V8 (1932-53)
05-26-2021, 12:08 PM
|
Replies: 24
Views: 3,462
|
Forum: Early V8 (1932-53)
05-25-2021, 02:22 PM
|
Replies: 24
Views: 3,462
|
Forum: Early V8 (1932-53)
05-25-2021, 02:20 PM
|
Replies: 24
Views: 3,462
|
Forum: Early V8 (1932-53)
05-25-2021, 02:05 PM
|
Replies: 24
Views: 3,462
|
Forum: Early V8 (1932-53)
02-09-2021, 10:10 AM
|
Replies: 42
Views: 4,593
|
Forum: Early V8 (1932-53)
01-22-2021, 03:03 AM
|
Replies: 6
Views: 1,247
|
Forum: Early V8 (1932-53)
01-02-2021, 04:17 AM
|
Replies: 14
Views: 1,607
Re: Adapting An OE Gas Tank Sender Unit
Be careful, on my tudor 37 I made a rubber gasket between the sending unit and the tank. Some days later it was smelling gas in the car... the rubber was melt by gasoline...
|
Forum: Early V8 (1932-53)
11-23-2020, 03:44 AM
|
Replies: 15
Views: 2,091
Re: Temperature
Kevin, I think like Alan; your stats are operating correctly!
mine are 160°F so they are closed until the temperature is 160°F; at this temperature they open and let the coolant circulate so the...
|
Forum: Early V8 (1932-53)
11-18-2020, 02:12 AM
|
Replies: 12
Views: 1,807
Re: 1936 radiator petcock
Yes it's very difficult to solder a radiator because the two boxes (top & bottom) are tin soldered, so if you heat too much the result will be leaks.
feufeu.
|
Forum: Early V8 (1932-53)
11-16-2020, 05:41 AM
|
Replies: 12
Views: 1,807
Re: 1936 radiator petcock
I had the same issueon my 37 radiator. wanted to replace the petcok and i broke it.
So i drilled a hole of 18mm in the radiator, and put in the hole a brass part I made. The internal of the part...
|
Forum: Early V8 (1932-53)
11-14-2020, 08:02 AM
|
Replies: 19
Views: 2,136
|
Forum: Early V8 (1932-53)
11-14-2020, 04:22 AM
|
Replies: 8
Views: 1,882
|
Forum: Early V8 (1932-53)
10-16-2020, 12:41 PM
|
Replies: 16
Views: 2,342
|