Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 24 of 24
Search took 0.00 seconds. Search: Posts Made By: stegomo
Forum: Early V8 (1932-53) 07-31-2022, 07:20 PM
Replies: 23
Views: 3,115
Posted By stegomo
Re: Electric fuel pump safety

I have an inertia switch that cuts power to the pump and ignition if the event of an accident
Forum: Early V8 (1932-53) 10-24-2021, 04:50 PM
Replies: 11
Views: 1,749
Posted By stegomo
Re: Electric power steering from a Saturn Vue into '54 Ford Customline

there is a 3 part video on this on youtube using saturn vue power steering into a shoebox
Forum: Early V8 01-23-2021, 11:59 AM
Replies: 0
Views: 420
Posted By stegomo
1950 Ford sedan

I'm looking for the steering shaft for a 1590 ford sedan, don't need the steering box just the shaft and doesn't need to be intact. only need the top 2 feet
Forum: Questions & Suggestions 05-18-2020, 09:26 AM
Replies: 1
Views: 1,252
Posted By stegomo
factory aluminum heads

Any suggestions on how to clean up aluminum heads and a coating for them?430803
Forum: Early V8 (1932-53) 05-02-2020, 03:25 PM
Replies: 125
Views: 23,135
Posted By stegomo
Re: engine photos

Thought i had the motor done, then i found these parts
Forum: Early V8 (1932-53) 12-26-2019, 05:15 PM
Replies: 17
Views: 2,736
Posted By stegomo
Re: Cranckcase blow by and how to handle the stank

Not applicable
Forum: Early V8 (1932-53) 11-21-2016, 08:45 PM
Replies: 18
Views: 3,003
Posted By stegomo
Re: Oil ring install

Managed to get them on and pistons in. ( I asked Lordco for a price on Hastings rings for my engine $519.00 )
Forum: Early V8 (1932-53) 11-21-2016, 09:41 AM
Replies: 18
Views: 3,003
Posted By stegomo
Re: Oil ring install

They are Mchenry rings for a 4 ring pistons
Forum: Early V8 (1932-53) 11-20-2016, 04:31 PM
Replies: 18
Views: 3,003
Posted By stegomo
Oil ring install

Starting to reassemble the engine and upper oil ring has 4 pieces but when I put them on the rings don't want to compress due to the inner piece holding them out
Forum: Early V8 (1932-53) 11-07-2016, 09:01 AM
Replies: 10
Views: 2,891
Posted By stegomo
Re: 8BA piston install

there is no mark on the piston tops,There is a vertical slot cut in one side of the skirt between the two oil rings should it go up or down?
Forum: Early V8 (1932-53) 11-07-2016, 08:03 AM
Replies: 7
Views: 2,006
Posted By stegomo
Re: 8CM camshaft

I paid $40 for one
Forum: Early V8 (1932-53) 11-06-2016, 11:18 PM
Replies: 7
Views: 2,006
Posted By stegomo
Re: 8CM camshaft

Thanks I will check it out
Forum: Early V8 (1932-53) 11-06-2016, 11:17 PM
Replies: 10
Views: 2,891
Posted By stegomo
8BA piston install

I know the piston pin is offset but there is no mark on the pistons to indicate which way to install. there is an oiling slot on the skirt, does it go up (intake side ) or down (exhaust side )?
Forum: Early V8 (1932-53) 11-06-2016, 09:33 PM
Replies: 7
Views: 2,006
Posted By stegomo
8CM camshaft

Anyone running an 8CM camshaft in an 8BA or thoughts on the idea?
Forum: Early V8 11-05-2016, 04:35 PM
Replies: 0
Views: 837
Posted By stegomo
Piston rings

Looking for a set of four ring 239 piston rings with 5/32 oil rings
Forum: Early V8 (1932-53) 05-13-2016, 11:17 PM
Replies: 7
Views: 1,465
Posted By stegomo
Re: 49T pistons in a 8BA

No there are no marks on them
Forum: Early V8 (1932-53) 05-13-2016, 10:34 PM
Replies: 7
Views: 1,465
Posted By stegomo
Re: 49T pistons in a 8BA

So all the aftermarket pistons that fit 39-53 have offset pins?
Forum: Early V8 (1932-53) 05-13-2016, 09:27 AM
Replies: 7
Views: 1,465
Posted By stegomo
Re: 49T pistons in a 8BA

Pistons from a pre 49 flathead V8
Forum: Early V8 (1932-53) 05-13-2016, 08:20 AM
Replies: 7
Views: 1,465
Posted By stegomo
49T pistons in a 8BA

Can you put 49T pistons in an 8BA engine?
Forum: Early V8 (1932-53) 04-30-2016, 09:23 PM
Replies: 4
Views: 1,414
Posted By stegomo
8BA crankshaft

Any ideas on how to remove front hub from the crankshaft ( the piece the front seal rides on )
Forum: Early V8 (1932-53) 04-10-2016, 06:02 PM
Replies: 1
Views: 945
Posted By stegomo
1950 Shoebox 4 door

Anyone ever done one piece side windows?
Forum: Early V8 (1932-53) 02-03-2016, 09:19 AM
Replies: 9
Views: 2,020
Posted By stegomo
Shoeboxford

Anyone know why this site has dissapeared? ,I can't find it
Forum: Early V8 (1932-53) 11-18-2015, 08:48 AM
Replies: 4
Views: 1,030
Posted By stegomo
Re: 1950 Meteor power brakes

Are you running a flathead V8? I was told it won't produce enough vacuum to operate the booster
Forum: Early V8 (1932-53) 11-17-2015, 11:38 AM
Replies: 4
Views: 1,030
Posted By stegomo
1950 Meteor power brakes

As I am putting an electric fuel pump in would it be possible to use the mechanical pump and a vacuum canister to work the booster?
Showing results 1 to 24 of 24

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:13 AM.