Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: swede
Forum: Model A (1928-31) 06-16-2016, 12:04 AM
Replies: 10
Views: 4,002
Posted By swede
Re: Oil fill tube loose

loose fill tube for oil can be tightened by using a nail punch to dimple about 1/2 inch up on the inside to make a small dent using a small hammer to indent the inside to make a "pimple" to make the...
Forum: Model A (1928-31) 07-06-2014, 09:06 AM
Replies: 17
Views: 4,984
Posted By swede
Re: Whatsup with carb setting?

Tom, I read your report concerning cleaning out the passageways. The #2 is blocked and I have worked for hours using every kind of wire to try to get to the cap jet. I can only get about 1/16th of an...
Forum: Model A (1928-31) 06-10-2014, 11:37 AM
Replies: 13
Views: 4,667
Posted By swede
Re: How do I remove the venturi ?

I just a new aluminum venturi and it is to big to fit the carb.
Can it be machined down to make it fit? It seems just a tad oversized.
Swede
Forum: Model A (1928-31) 05-05-2014, 12:03 AM
Replies: 7
Views: 1,522
Posted By swede
Re: Horn button

I have an original
Forum: Model A (1928-31) 05-03-2014, 12:11 PM
Replies: 7
Views: 1,522
Posted By swede
Re: Horn button

my horn works only when I connect one wire, button does not work on the steering wheel. What could be the problem? The harness wires connections work everywhere else.
Newbie Swede
Forum: Model A (1928-31) 04-28-2014, 11:05 AM
Replies: 8
Views: 3,472
Posted By swede
Re: Model A Horn

Is it possible to purchase new 6V coils from somewhere? I took my horn apart and notices one set of coils was black. I do not want to purchase a repo horn or pay over 250 dollars for a replacement. ...
Forum: Model A (1928-31) 04-21-2014, 06:17 PM
Replies: 25
Views: 8,421
Posted By swede
Re: engine vibration

I just got my 1931 Model A deluxe coupe that needed complete wire job. That is done and after it did not start I read all you guys and thanks a million and now it starts, but at 15 miles an hour I...
Forum: Questions & Suggestions 03-30-2014, 08:44 AM
Replies: 2
Views: 1,177
Posted By swede
Re: rumble seat upper rubber bumpers

I was not getting any response elsewhere, even in my model a restorer's book.
Forum: Model A (1928-31) 03-29-2014, 10:56 PM
Replies: 2
Views: 1,608
Posted By swede
Wink 1931 model A coupe

Rubber bumpers for the rumble seat seem to be hard to put in and was wondering if there is a means or method to install the new bumpers that fit on the top of the lid.
Any help would be appreciated...
Forum: Questions & Suggestions 03-27-2014, 11:33 AM
Replies: 2
Views: 1,177
Posted By swede
Question rumble seat upper rubber bumpers

How do you install the large bumper into the small hole on my 1931 model A coupe? there are two holes for the lid to rest on at the top of the opening. I orders two new bumpers and cannot figure out...
Showing results 1 to 10 of 10

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:13 PM.