Forum: Model A (1928-31)
09-01-2015, 02:29 PM
|
Replies: 24
Views: 5,026
|
Forum: Model A (1928-31)
09-01-2015, 01:34 PM
|
Replies: 24
Views: 5,026
Body Wood Suppliers
Has any Fordor body owners had experience with body wood supplied by Classic Wood in NC?
|
Forum: Model A (1928-31)
08-31-2015, 01:06 PM
|
Replies: 10
Views: 1,914
Re: Body Wood
Thank you. Were you satisfied with their product? Do you know of anyone who has bought the fordor kit?
|
Forum: Model A (1928-31)
08-31-2015, 11:33 AM
|
Replies: 10
Views: 1,914
Body Wood
Can anyone recomend a good body wood supplier for Model A Fordor Sedans? I have a 60-C Briggs Steelback. I have heard that wood kits for different suppliers do not fit and drilled holes do not match...
|
Forum: Model A (1928-31)
07-28-2014, 05:28 PM
|
Replies: 3
Views: 1,246
|
Forum: Model A (1928-31)
07-28-2014, 12:48 PM
|
Replies: 3
Views: 1,246
Brake Levers
Which side do rear brake levers (that attach to brake rods) that slip on break actuators goes toward the backing plate and hub - flat or beveled side? Same question on emergency brake levers.
|
Forum: Model A (1928-31)
11-01-2013, 08:57 PM
|
Replies: 17
Views: 2,393
Re: Backfiring
Turned out to be carb. Installed another cab. after checking compression on each cylinder and ran good. Plenty of power. Old carb was wrapped and sucking air. Thanks for everyone's help.
|
Forum: Model A (1928-31)
10-31-2013, 08:47 PM
|
Replies: 17
Views: 2,393
Re: Backfiring
Thanks guys. Found that the spark is not strong as it should be. Installed coil, points, and condenser but still not as strong as my other car that runs correctly. Any other idea of what could cause...
|
Forum: Model A (1928-31)
10-30-2013, 11:52 PM
|
Replies: 17
Views: 2,393
Backfiring
Popping back through carb . When accelerated.
Bogs down when accelerated and pops. Is this a
Carb, intake manifold, or firing issue?
|
Forum: Model A (1928-31)
10-30-2013, 11:22 PM
|
Replies: 6
Views: 2,108
Timing Gear
Are aluminum timing gears noisier
Than fiber gears? Will a new metal timing and crank
Shaft gear mesh in over time and get quiter?
|
Forum: Model A (1928-31)
08-27-2013, 06:55 PM
|
Replies: 8
Views: 1,981
Re: Radiator
Tom:
Is there a shroud on model A radiators other than the radiator the shell?
|
Forum: Model A (1928-31)
08-25-2013, 11:24 PM
|
Replies: 8
Views: 1,981
Radiator
Anyone had experience with Berg's radiators in Il?
Did original radiators for 1929 have vertical tubes two deep or were they three deep? Round or flat?
|
Forum: Model A (1928-31)
08-09-2013, 01:48 PM
|
Replies: 31
Views: 14,461
Re: Babbitt or inserts
My engine was rebuilt by a local shop. They did not por rods and mains. When started up engine has a knock like a rod or main for about 5 seconds then runs smooth. Oil seems not to stay in journal...
|
Forum: Model A (1928-31)
08-08-2013, 09:31 PM
|
Replies: 31
Views: 14,461
Babbitt or inserts
Any recommendations for rebuilding engine with inserts vs. pouring rods and mains with Babbitt?
Any experience with James Rogers in N.C. or Richard F. In Il.?
|
Forum: Model A (1928-31)
07-21-2013, 03:50 PM
|
Replies: 7
Views: 2,944
Engine Knock
I recently had my model A engine rebuilt. The first time it starts each day, there is a knock that sounds like a piston slab. Very noticeable. It only last for a few seconds then goes away. Sound...
|
Forum: Model A (1928-31)
07-15-2013, 10:53 PM
|
Replies: 8
Views: 1,497
Re: condenser
how long should the screw be? The condenser came with a copper screw.
|
Forum: Model A (1928-31)
07-15-2013, 10:46 PM
|
Replies: 8
Views: 1,497
|
Forum: Model A (1928-31)
07-15-2013, 10:26 PM
|
Replies: 8
Views: 1,497
Re: condenser
thank you. If I understand, it goes between the condenser tip and bar on the passenger side of the car and the copper screw goes in the drivers side of the car though the bar into the condenser,
|
Forum: Model A (1928-31)
07-15-2013, 09:34 PM
|
Replies: 8
Views: 1,497
condenser
Is there a fiber spacer that goes between the condenser and the lower distributor plate. The condenser grounds to the distributor on the side and there is a brass or copper screw that screws in the...
|
Forum: Model A (1928-31)
03-31-2013, 09:33 AM
|
Replies: 11
Views: 2,436
|
Forum: Model A (1928-31)
03-30-2013, 10:59 PM
|
Replies: 11
Views: 2,436
|
Forum: Model A (1928-31)
03-30-2013, 10:00 PM
|
Replies: 11
Views: 2,436
Re: Rear Motor Supports
Thanks. I got the rubber from Berts. The bolts he got from Synders. Can you give me instructions on how they fit? Inside rubber with extension toward frame and metal extensions through...
|
Forum: Model A (1928-31)
03-30-2013, 09:05 PM
|
Replies: 11
Views: 2,436
Rear Motor Supports
New rear motor support rubber. Les Andrews book recommends cutting the extensions (tips) off the inside rubber as well as the bottom right angle piece as the extensions do not fit the frame holes...
|
Forum: Model A (1928-31)
03-29-2013, 10:47 PM
|
Replies: 10
Views: 2,302
|
Forum: Model A (1928-31)
03-29-2013, 09:54 PM
|
Replies: 10
Views: 2,302
Re: Transmission grease
Ford 3
Would u take the pressure plate off and get the clutch disk out or just take a screw driver on a rag and try to wipe the grooves clean?
|