Forum: Model A (1928-31)
11-30-2023, 02:17 PM
|
|
Replies: 11
Views: 1,077
|
|
Forum: Model A (1928-31)
10-10-2023, 08:21 AM
|
|
Replies: 31
Views: 2,421
Re: Air Filter or not
I run a stock Zenith with a k&n high boy filter and have had no issues whatsoever. Dennis
|
|
Forum: Model A (1928-31)
07-25-2023, 06:38 PM
|
|
Replies: 20
Views: 2,141
|
|
Forum: Model A (1928-31)
07-25-2023, 06:36 PM
|
|
Replies: 20
Views: 2,141
Re: rear hub bearings
I haven’t found a source for the hub sleeve races by themselves.The bearings that come with those races don’t hold up and I wouldn’t use them.I found now v8 bearings on eBay and am using them.Dennis
|
|
Forum: Model A (1928-31)
03-17-2023, 02:35 PM
|
|
Replies: 16
Views: 2,816
Re: Oil Filler Tube
I had the same problem with my rebuilt engine several years ago,I had a B fill pipe and cap so I installed it and solved the problem. Its still on there with no leakage.
|
|
Forum: Model A (1928-31)
01-29-2023, 04:25 PM
|
|
Replies: 14
Views: 2,338
Re: long warm up
May be obvious but if it has a vacuum wiper make sure that It is not the source of an air leak . My car had a split rubber hose at the vacuum motor causing a similar symptom.
|
|
Forum: Model A (1928-31)
01-20-2023, 11:08 PM
|
|
Replies: 57
Views: 10,762
Re: Cluster bearing solution?
I would drag a sharp file across the edge of the end cages ,if the file does not remove any metal but bounces over them they may be hardened enough to hold up in service.If the file removes metal I...
|
|
Forum: Model A (1928-31)
01-04-2023, 06:50 PM
|
|
Replies: 16
Views: 3,172
|
|
Forum: Model A (1928-31)
12-28-2022, 08:17 PM
|
|
Replies: 5
Views: 1,353
|
|
Forum: Model A (1928-31)
10-05-2022, 08:45 AM
|
|
Replies: 23
Views: 4,354
Re: Mitchell overdrive
I have a 30 Tudor with a AER touring engine with 5.5 head,V8 wheels 600-16 tires,3.54 gears..I like this combination very much.Not to many steep hills in my area but has no problem with them.I would...
|
|
Forum: Model A (1928-31)
05-14-2022, 03:07 PM
|
|
Replies: 17
Views: 3,425
Re: DIY Pin Striping
Thanks Ed in Maine for the advise on diy pinstriping.I couldnt find a local striper and my car has been done for 4+years .I did eveything on the car except the engine so why not the pinstripe too?Its...
|
|
Forum: Model A (1928-31)
05-01-2022, 02:17 PM
|
|
Replies: 51
Views: 9,353
|
|
Forum: Model A (1928-31)
04-21-2022, 12:49 PM
|
|
Replies: 36
Views: 5,783
|
|
Forum: Model A (1928-31)
03-29-2022, 05:02 PM
|
|
Replies: 11
Views: 1,310
|
|
Forum: Model A (1928-31)
03-25-2022, 10:02 AM
|
|
Replies: 5
Views: 748
Re: Tires
No,it won’t be better steering it will be unstable ,as in dangerous.
|
|
Forum: Model A (1928-31)
03-16-2022, 11:47 AM
|
|
Replies: 23
Views: 2,515
Re: Rear Wheel bearing source?
In my experience with reproduction wheel bearings I have found the end cages to be by heat treated and to soft.This allows the rollers to wear the cage get free,also metal worn from the cage...
|
|
Forum: Model A (1928-31)
03-09-2022, 04:59 PM
|
|
Replies: 10
Views: 1,642
|
|
Forum: Model A (1928-31)
03-03-2022, 05:27 PM
|
|
Replies: 7
Views: 1,564
Re: High fill primer
My experience with k200 is that it shrinks over time and pulls loose .I would not use it .
|
|
Forum: Model A (1928-31)
03-03-2022, 05:17 PM
|
|
Replies: 10
Views: 1,466
Re: Air Filter?
I use a highboy with K&n filter on stock Zenith or Tillotson with no issues.
|
|
Forum: Model A (1928-31)
03-03-2022, 03:42 PM
|
|
Replies: 20
Views: 2,338
|
|
Forum: Model A (1928-31)
03-02-2022, 12:56 PM
|
|
Replies: 56
Views: 8,166
Re: You ever do something reallySTUPID?
I was installing a shrinking disc on a fender grinder .The grinder was on the floor and still plugged in,my foot on the handle of the grinder.All my fingers were wrapped around the edge of the disc...
|
|
Forum: Model A (1928-31)
02-23-2022, 01:28 PM
|
|
Replies: 14
Views: 2,153
|
|
Forum: Model A (1928-31)
12-31-2021, 07:47 PM
|
|
Replies: 26
Views: 4,196
|
|
Forum: Model A (1928-31)
12-24-2021, 08:43 AM
|
|
Replies: 89
Views: 23,277
|
|
Forum: Model A (1928-31)
12-24-2021, 08:41 AM
|
|
Replies: 5
Views: 928
|
