Forum: Early V8 (1932-53)
05-16-2023, 06:53 PM
|
Replies: 154
Views: 31,270
|
Forum: Early V8 (1932-53)
04-20-2023, 04:06 PM
|
Replies: 62
Views: 4,592
|
Forum: Early V8 (1932-53)
11-16-2022, 09:17 AM
|
Replies: 9
Views: 1,006
|
Forum: Early V8 (1932-53)
04-27-2022, 06:29 PM
|
Replies: 6
Views: 629
|
Forum: Early V8 (1932-53)
04-19-2022, 01:01 PM
|
Replies: 106
Views: 9,257
|
Forum: Early V8 (1932-53)
12-14-2021, 06:29 PM
|
Replies: 60
Views: 6,954
|
Forum: Early V8 (1932-53)
11-26-2021, 06:32 PM
|
Replies: 11
Views: 1,513
|
Forum: Early V8 (1932-53)
11-25-2021, 06:40 PM
|
Replies: 11
Views: 1,513
|
Forum: Early V8 (1932-53)
11-25-2021, 10:14 AM
|
Replies: 11
Views: 1,513
carburator
I have a four bolt mercury intake I want to go to a GM two barrel witch carb should I use /
|
Forum: Early V8 (1932-53)
03-04-2021, 12:26 PM
|
Replies: 14
Views: 2,355
|
Forum: Early V8 (1932-53)
03-02-2021, 09:38 PM
|
Replies: 16
Views: 1,456
Re: bore
I am using the three piece ring i have three types of ring compressers .
my favorite is a clamp type thanks to all of you you have no idea how much help you have been this is my last build I am...
|
Forum: Early V8 (1932-53)
03-02-2021, 04:16 PM
|
Replies: 16
Views: 1,456
Re: bore
thank you all I now have all my ducks in a row I am not a kiwi but i am an Ohio Buckeye that is a useless nut.
|
Forum: Early V8 (1932-53)
03-02-2021, 03:17 PM
|
Replies: 16
Views: 1,456
|
Forum: Early V8 (1932-53)
03-02-2021, 02:43 PM
|
Replies: 16
Views: 1,456
bore
I have a .0040 over bore on an 8ba I know this is basic but what is the bore in inches ? i am having a problem my pistons are very tight in the bore. I have to tap them to get them installed. I...
|
Forum: Early V8 (1932-53)
02-08-2021, 04:20 PM
|
Replies: 5
Views: 1,238
|
Forum: Early V8 (1932-53)
02-07-2021, 04:32 PM
|
Replies: 5
Views: 1,238
heads
I have a set of EBA heads What i need to know is it worth having them milled or just leave them alone
|
Forum: Early V8 (1932-53)
02-03-2021, 09:53 AM
|
Replies: 9
Views: 1,456
|
Forum: Early V8 (1932-53)
02-01-2021, 10:18 AM
|
Replies: 9
Views: 1,456
Re: "help"
thank you all I will now be able to get the job done correctly .
|
Forum: Early V8 (1932-53)
01-30-2021, 03:05 PM
|
Replies: 9
Views: 1,456
|
Forum: Early V8 (1932-53)
01-30-2021, 02:24 PM
|
Replies: 9
Views: 1,456
"help"
I can't remember if the cylinders have to be beveled after boring . I found a problem with my new Hastings rings the third ring is a three part ring . some of the thin rings were bent . I am sure it...
|
Forum: Early V8 (1932-53)
01-24-2021, 04:58 PM
|
Replies: 20
Views: 2,768
Re: "help"
Everything checked out on the main bearings and rod bearings .I could turn the motor over with a breaker bar with 4 pistons installed ,but it was stiff . as I installed the rest of them it got...
|
Forum: Early V8 (1932-53)
01-24-2021, 12:45 PM
|
Replies: 20
Views: 2,768
Re: "help"
0040 bore new pistons . That is a fresh bore .no ridge
|
Forum: Early V8 (1932-53)
01-24-2021, 12:21 PM
|
Replies: 20
Views: 2,768
"help"
I am building a 8ba I install new rings and now I have to use a pipe wrench with a piece of pipe to turn the motor over. The rings are hastings . I am concerned . I don't believe the starter will...
|
Forum: Early V8 (1932-53)
01-11-2021, 09:47 AM
|
Replies: 22
Views: 5,134
|
Forum: Early V8 (1932-53)
04-25-2020, 02:33 PM
|
Replies: 61
Views: 6,623
|