Forum: Early V8
05-17-2024, 12:00 PM
|
|
Replies: 0
Views: 51
|
|
Forum: Early V8
05-17-2024, 11:55 AM
|
|
Replies: 0
Views: 29
|
|
Forum: Early V8 (1932-53)
05-16-2024, 06:42 PM
|
|
Replies: 2
Views: 162
32 press on cam gear
I am working on a 32 V8 engine. The gear that came with the engine looks fine but I don’t know the history. I have some new old replacement gears. I would like opinions whether to put a replacement...
|
|
Forum: Early V8
04-30-2024, 03:23 PM
|
|
Replies: 1
Views: 315
Re: 32 parts
I would send pictures of anything somebody is interested in.
|
|
Forum: Early V8 (1932-53)
04-26-2024, 11:38 AM
|
|
Replies: 13
Views: 891
Re: Removing perch bolt for repair
This is how I remove shackles. I put the car on jackstands and put floor jacks under the spring ends. If you jack one up so the shackle is level you will be able to jack the other one up until the...
|
|
Forum: Early V8
04-25-2024, 05:32 PM
|
|
Replies: 1
Views: 315
32 parts
I have three bottom of the column switches. Two are NOS. One still has as new plating but some very small rust specks. Very minor. _$30
One has no rust at all but the plating is weathered. Still NOS...
|
|
Forum: Early V8 (1932-53)
04-18-2024, 08:35 PM
|
|
Replies: 27
Views: 1,904
Re: Narrow V8 Rear Axle
I have a Maverick in my car. It has the 1 in adapters. The total width is 58 in. The wheels fit over the drums. you would need the 3/16 rings to fit in the wheels for support
|
|
Forum: Early V8 (1932-53)
03-28-2024, 09:36 AM
|
|
Replies: 13
Views: 1,102
Re: EE-01 carb base
I made my own inserts. I forget what thread I used, but I tapped the bowl out to fit. I used a fine thread bolt. I drilled and tapped the bolt with the correct tread for the seat fitting. The...
|
|
Forum: Early V8 (1932-53)
03-02-2024, 05:29 PM
|
|
Replies: 9
Views: 782
Re: Steering box mystery
The brass tube is for use with a horn rod. You can add a bracket and retain the switch at the box. The steel tube is for use with the wire setup.
The brass one is very sought after.
|
|
Forum: Early V8
02-24-2024, 02:52 PM
|
|
Replies: 0
Views: 173
One 46-48 Drum
Very nice original drum. It measures .020 oversize. It has a small chunk missig on the outside band. I have an another drum as a doner for the chunk I did an experiment on another drum and tack...
|
|
Forum: Early V8
02-24-2024, 02:44 PM
|
|
Replies: 0
Views: 126
Excellent 46-48 front hubs drums.
I fine pair of original drums. The diameters are only over size .020 They still have paint from decades ago. Studs, bearings are all fine. Pictures later.
|
|
Forum: Early V8
02-24-2024, 02:35 PM
|
|
Replies: 2
Views: 318
|
|
Forum: Early V8
02-24-2024, 02:30 PM
|
|
Replies: 2
Views: 290
|
|
Forum: Early V8 (1932-53)
02-19-2024, 10:07 PM
|
|
Replies: 5
Views: 474
|
|
Forum: Early V8
02-15-2024, 02:26 PM
|
|
Replies: 2
Views: 290
|
|
Forum: Early V8
02-15-2024, 02:24 PM
|
|
Replies: 2
Views: 318
|
|
Forum: Early V8 (1932-53)
02-12-2024, 06:34 PM
|
|
Replies: 9
Views: 751
|
|
Forum: Early V8
02-10-2024, 12:12 PM
|
|
Replies: 2
Views: 318
Clam shell Torque Tube Coupler
Very nice clam shell coupler. There are a couple of small worn spots on one of the halves where something got in it during installation. It does not matter at all. 99% of the surface is great. The...
|
|
Forum: Early V8
02-10-2024, 11:45 AM
|
|
Replies: 2
Views: 290
28-48 U-Joint
Extremely nice U-Joint. I can not detect any play at all in the joints. It is as tight as it can be and still move freely. It has a little surface rust. A Evap O Rust dip or just a soak in WD 40...
|
|
Forum: Early V8 (1932-53)
02-09-2024, 09:58 PM
|
|
Replies: 1
Views: 360
|
|
Forum: Early V8
02-05-2024, 10:54 AM
|
|
Replies: 2
Views: 351
|
|
Forum: Early V8
02-04-2024, 01:01 PM
|
|
Replies: 0
Views: 223
32 Column mount delivery driver note pad
This is a pad mount that attached to a steering column. I took it off a 32 truck. It was used so the driver had a list of delivery addresses. It is slightly rusted but would clean up with bead...
|
|
Forum: Early V8
01-16-2024, 01:23 PM
|
|
Replies: 0
Views: 162
32 5W back glass original
Original un-cracked back glass. It was damaged when it was not completely rolled down when the body was blasted. It could be polished out or used for a pattern.
|
|
Forum: Early V8
01-13-2024, 07:32 PM
|
|
Replies: 2
Views: 351
|
|
Forum: Early V8
01-07-2024, 09:34 AM
|
|
Replies: 2
Views: 351
Oil bath air filter 33-36
Very nice filter. It fits Stromberg carbs. It will not fit a 32 Detroit Lub. carb. Original paint. No damage except the hose is stiff.
|
