Forum: Model-A
09-10-2019, 04:29 PM
|
Replies: 3
Views: 1,508
|
Forum: Model-A
09-10-2019, 04:27 PM
|
Replies: 3
Views: 1,456
|
Forum: Model-A
08-03-2019, 11:18 AM
|
Replies: 3
Views: 1,508
|
Forum: Model-A
06-10-2019, 10:09 PM
|
Replies: 3
Views: 1,456
|
Forum: Model-A
06-07-2019, 04:32 PM
|
Replies: 3
Views: 1,508
|
Forum: Model-A
06-07-2019, 04:32 PM
|
Replies: 3
Views: 1,456
|
Forum: Model-A
06-06-2019, 05:59 PM
|
Replies: 3
Views: 1,456
|
Forum: Model-A
06-03-2019, 08:12 PM
|
Replies: 3
Views: 1,508
|
Forum: Model A (1928-31)
06-02-2019, 08:35 AM
|
Replies: 4
Views: 1,233
|
Forum: Model A (1928-31)
06-02-2019, 08:34 AM
|
Replies: 4
Views: 1,233
|
Forum: Model A (1928-31)
06-01-2019, 02:46 PM
|
Replies: 12
Views: 3,812
|
Forum: Model A (1928-31)
06-01-2019, 02:23 PM
|
Replies: 4
Views: 1,233
LeBaron Top Boot Fitment
Hello might anyone know are any of the LeBaron top boots interchangeable?
Im looking for a standard Phaeton. However I keep finding lots of standard Roadster (which has less material so I would...
|
Forum: Model A (1928-31)
04-25-2019, 12:16 PM
|
Replies: 4
Views: 1,469
Radiator Shell Badge Mountin...How to??
Hello I have a 31 radiator shell and purchased an aftermarket black script FORD top badge to be installed. It has the "cup" behind. Whats the best way to flare the cup without damage to install?
|
Forum: Model A (1928-31)
04-25-2019, 10:07 AM
|
Replies: 38
Views: 10,209
Mikesspeedshop NC-Shock Rebuilder BEWARE
Greetings all. As we look to have our shocks rebuilt from time to time I wanted to share my story.
Back in Feb I reached out to Mike Baetlett. Several emails here on FordBarn and then personal...
|
Forum: Model A (1928-31)
03-21-2019, 11:23 AM
|
Replies: 12
Views: 3,812
Re: Main Wiring Harness 1929 Questions
Seems that it would work, my issue was that the two green wires for the switch were rather short and would not extend from the frame rail. I was thinking of cutting them soldering in an extension so...
|
Forum: Model A (1928-31)
03-20-2019, 06:06 PM
|
Replies: 12
Views: 3,812
|
Forum: Questions & Suggestions
02-09-2019, 09:56 PM
|
Replies: 3
Views: 2,299
Re: Model A body lift
Nice post. Im pulling my 31 phaeton from the frame and swapping chassis. Where did you find order of operations?
|
Forum: Model A (1928-31)
06-14-2016, 09:36 AM
|
Replies: 23
Views: 5,791
Re: Zenith rebuilt. No power past 40mph
Also I noticed there is a small bit of play in the throttle shaft. However does not effect idle so I didnt think it would impact high end speed performance.
|
Forum: Model A (1928-31)
06-14-2016, 09:25 AM
|
Replies: 23
Views: 5,791
Re: Zenith rebuilt. No power past 40mph
Morning-I used the heated ultrasonic and each passage was blown out with 70psi of steam (a steam boiler we use in the Jewelry industry which has a fine tip outlet) and yes all jets were removed,...
|
Forum: Model A (1928-31)
06-13-2016, 08:26 PM
|
Replies: 23
Views: 5,791
Re: Zenith rebuilt. No power past 40mph
Mr Miller, good point. I recently replaced dist., points and cap and button. All adjusted to spec along with TDC of #1 on contact. Let me let her cool off tonight and Ill check the timing.
|
Forum: Model A (1928-31)
06-13-2016, 08:18 PM
|
Replies: 23
Views: 5,791
Re: Zenith rebuilt. No power past 40mph
Mitch- I read the attached link to the main jet artificial on rebuilding. Appears to address my issues with high speed power. Without flow testing I am left with purchasing calibrated jets. I didnt...
|
Forum: Model A (1928-31)
06-13-2016, 08:13 PM
|
Replies: 23
Views: 5,791
Re: Zenith rebuilt. No power past 40mph
Utopia- I did turn the GAV open up-to two turns then back down to damn near off. Not a substantial change. All while running 40mph made an impact when open, some popping.
|
Forum: Model A (1928-31)
06-13-2016, 07:31 PM
|
Replies: 23
Views: 5,791
Zenith rebuilt. No power past 40mph
Greetings. I am a jewelry who used my ultrasonic and steam generator to clean and inspect (10x magnification) a few old zenith carbs, pieces and parts to make two good units. The two run really well,...
|