Forum: Model A (1928-31)
07-26-2020, 11:53 AM
|
Replies: 0
Views: 212
Body mounting
I'm ready to mount my 30 std coupe body on the frame. Are any of you aware of any publication showing the order of mounting? Start with running boards, and shields, front fenders, rear bumper...
|
Forum: Model A (1928-31)
07-10-2020, 01:09 PM
|
Replies: 6
Views: 643
Re: Windshield Frame Press-In Nut
All good comments, thank you. I'll measure the ID of the hole in relationship to the knurled nut and enlarge the hole slightly - plus the JB treatment.
|
Forum: Model A (1928-31)
07-09-2020, 05:37 PM
|
Replies: 6
Views: 643
Windshield Frame Press-In Nut
Do any of you have any experience with installing a "windshield frame press-in nut" (Bratton's part #30100)? I've got a 30 Std Cpe with a recently painted frame and it is in excellent condition with...
|
Forum: Model A (1928-31)
02-09-2020, 09:52 AM
|
Replies: 38
Views: 5,808
Re: Hinge pins
Hey desotoguy, that was the information I was seeking. I understand the location where you place the thin nylon washer. Could you send a picture? My care is a user, not a point car and I like your...
|
Forum: Model A (1928-31)
02-06-2020, 10:56 AM
|
Replies: 38
Views: 5,808
Re: Hinge pins
For my 30 standard coupe, I've removed my pins with a bit of difficulty and found the drill both sides method, then punch through works best. The "C" clamp shaped press was a waste money! Once I...
|
Forum: Model A (1928-31)
11-21-2019, 06:32 PM
|
Replies: 14
Views: 1,343
Re: #1 plug question
Gentlemen, I appreciate all of your responses. The entire distributor has been completely rebuilt and there is no play in the shaft. I believe the issue may be w/the contact points in the new cap....
|
Forum: Model A (1928-31)
11-20-2019, 01:40 PM
|
Replies: 14
Views: 1,343
#1 plug question
I'm assembling my 30 Std Coupe with a recently rebuilt engine. It starts immediately yet runs a bit rough. I placed a sensor on all four Champion plugs and found the #1 plug does not fire...
|
Forum: Model A (1928-31)
10-27-2019, 10:50 AM
|
Replies: 1
Views: 700
top molding questions
For my '30 standard coupe, I'm debating over using the hidum welt versus the aluminum molding for the strip above the visor. My car will be a driver; it is already painted and the long-grain vinyl...
|
Forum: Model A (1928-31)
01-08-2019, 12:46 PM
|
Replies: 3
Views: 690
Re: top material installation
You nailed it exactly Steve. It will be easy to wait and install the top over the warmer months and it makes a lot of sense. Thanks for the response!
|
Forum: Model A (1928-31)
01-08-2019, 08:32 AM
|
Replies: 3
Views: 690
top material installation
I'm ready to install the top material in my 30 coupe which has been painted, assembled on the chassis, etc. I read in one article that the upholstery should be installed first for ease of...
|
Forum: Model A (1928-31)
12-24-2018, 09:12 AM
|
Replies: 16
Views: 1,650
Re: Front windshield rubber for closed car
I'd like to know how you install the windshield weatherstrip around the side of the windshield frame where the square nuts (one on each side) are located in the bead channel? Do you notch the bead? ...
|
Forum: Model A (1928-31)
10-07-2018, 06:11 AM
|
Replies: 7
Views: 1,164
Re: body reassembly
OK, perhaps I should have been more specific. I removed the body from my 30 coupe over 20 years ago which included a complete disassembly of all fenders, removal of the gas tank, running boards,...
|
Forum: Model A (1928-31)
10-06-2018, 07:35 AM
|
Replies: 7
Views: 1,164
body reassembly
I just completed a body off frame restoration of my 30 standard coupe. Do any of you have a body reassembly order?
|
Forum: Model A (1928-31)
09-13-2018, 08:05 AM
|
Replies: 11
Views: 1,226
add temperature probe
Have any of you drilled and tapped a cast gooseneck to install a temperature probe? There seems to be enough material and there isn't much pressure. I could change the gooseneck or install the...
|
Forum: Early V8 (1932-53)
07-13-2017, 08:04 AM
|
Replies: 10
Views: 2,461
Re: How to install running board stainless trim
I'm new to your forum and will be asking a lot of questions. To start, I'm installing the running board trim on a 1930 Standard coupe that I'm restoring. I purchased the SS trim from Mac's. Does...
|