Forum: Model A (1928-31)
09-13-2021, 06:49 AM
|
Replies: 31
Views: 5,362
Re: Pressurized Radiator
I am tired of carrying around 3 gallons of water with me every time I i go out because the A belches water all over the place.
|
Forum: Model A (1928-31)
09-12-2021, 07:57 AM
|
Replies: 0
Views: 427
|
Forum: Model A (1928-31)
09-12-2021, 07:55 AM
|
Replies: 31
Views: 5,362
Pressurized Radiator
Does anyone out there run a pressurized radiator? Can you tell me how and where to mount the overflow tube?
Thank you,
|
Forum: Model A (1928-31)
01-14-2021, 05:53 PM
|
Replies: 133
Views: 272,644
Re: Manners... A new rule...
i quit coming to this forum because of the rude comments that I received.
I may return because of your hard work.
Thank you,
|
Forum: Model A (1928-31)
01-13-2021, 02:52 PM
|
Replies: 19
Views: 3,083
Re: Fog Light Switch Help
May I ask, what is the purpose of the fog lights? Is this an accessory, or did Ford install them originally?
Thanks,
|
Forum: Model A (1928-31)
11-03-2020, 06:52 PM
|
Replies: 8
Views: 1,861
Re: Horn
On my A, I added a ground wire for all six of the lights, the horn, and finally the engine to the frame. Grounds or lack there of, can be real gremlins.
|
Forum: Model A (1928-31)
10-31-2020, 01:55 PM
|
Replies: 26
Views: 13,989
Re: Adjusting ahooga horn
I had to add a aground to my horn. In fact, I have added a separate ground for each of the lights. Finally, I added a ground from the engine to the frame.
|
Forum: Model-A
10-28-2020, 05:30 PM
|
Replies: 0
Views: 453
19" Roller Tires
Four (4) 4.75 x 10" roller tires.
Free
You pay for shipping and handling
|
Forum: Model A (1928-31)
09-13-2020, 08:01 PM
|
Replies: 6
Views: 809
|
Forum: Model A (1928-31)
09-13-2020, 12:40 PM
|
Replies: 6
Views: 809
|
Forum: Model A (1928-31)
09-03-2020, 01:27 PM
|
Replies: 15
Views: 1,664
Re: 12 volt?
I started my restoration 7 years ago. At that time, there existed only 12 v led lights. I wanted LED lights in the rear to be seen. I also wanted to be able to get home if I were caught out after...
|
Forum: Model A (1928-31)
09-03-2020, 01:20 PM
|
Replies: 13
Views: 2,695
Re: undercoat running boards?
I put POR 15 on everything under the vehicle and frame. It seals with the metal and does not trap moisture. It is wicked stuff. Two pair of gloves and long sleeve shirts a must. Do NOT get it on any...
|
Forum: Model A (1928-31)
07-31-2020, 07:36 PM
|
Replies: 0
Views: 523
|
Forum: Model-A
07-18-2020, 02:34 PM
|
Replies: 0
Views: 475
|
Forum: Model A (1928-31)
09-29-2019, 04:11 PM
|
Replies: 6
Views: 1,744
Model A Headlights
Disregard this post. These lights are not for a Model A.
My original headlights have seen better days.
How do I go about rehabilitating them?
Were these headlights originally chrome...
|
Forum: Model A (1928-31)
08-19-2019, 07:46 PM
|
Replies: 2
Views: 1,256
|
Forum: Model A (1928-31)
08-19-2019, 06:41 PM
|
Replies: 13
Views: 2,047
12 VDC Wiring
What changes are required to the attached drawing for using a 12 VDC Negative ground vs the 6 VDC positive ground?
Does a similar drawing exist for the 12 VDC Neg Ground?
thanks,
|
Forum: Model A (1928-31)
08-10-2019, 07:35 PM
|
Replies: 16
Views: 2,426
Re: Engine no run
1. I cleaned the carburetor inlet ball valve. It was plugged. The valve now works clean and great.
2. I put 2 tablespoons Marvel Mystery Oil into each cylinder. Two hours later I came back and...
|
Forum: Model A (1928-31)
08-10-2019, 05:24 AM
|
Replies: 6
Views: 1,647
|
Forum: Model A (1928-31)
08-10-2019, 04:35 AM
|
Replies: 16
Views: 2,426
|
Forum: Model A (1928-31)
08-09-2019, 08:51 PM
|
Replies: 16
Views: 2,426
|
Forum: Model A (1928-31)
08-09-2019, 08:33 PM
|
Replies: 16
Views: 2,426
Engine no run
Wednesday afternoon, my A engine ran pretty well it ran well for almost 15 minutes and then just quit. I can not get it to run again.
Today, a fellow club member came by to help.
We were able to...
|
Forum: Model A (1928-31)
08-08-2019, 09:49 AM
|
Replies: 3
Views: 1,219
31 Locking Door Handle Shaft Dimensions
Can anyone out there in Model A land be able to tell me the dimensions marked in RED ?
There is no vendor supplying the locking door handle manufactured per the attached.
Thanks,
|
Forum: Model A (1928-31)
08-01-2019, 06:31 PM
|
Replies: 0
Views: 994
Windshield Frame Nut
I am working on restoring an original windshield frame. It requires a lot of work. One thing I am looking at is the windshield frame nut.
How is the nut installed? Is it pressed into the frame?...
|
Forum: Model A (1928-31)
07-31-2019, 07:42 PM
|
Replies: 7
Views: 1,701
|