Forum: Model A (1928-31)
04-28-2021, 09:34 PM
|
|
Replies: 5
Views: 1,017
Re: Rear spring
Update, the top leaf has the "Ford" logo stamped on it, that was cool to see. It also is beveled as stated earlier.
|
|
Forum: Model A (1928-31)
04-27-2021, 01:16 PM
|
|
Replies: 5
Views: 1,017
Rear spring
OK, I was under my 1928 coupe and noticed that the 2 smallest leaf springs are mounted on the bottom [under the main spring]. Does anyone know why someone would do this?:confused:
|
|
Forum: Model A (1928-31)
05-15-2020, 02:51 PM
|
|
Replies: 3
Views: 1,266
|
|
Forum: Model A (1928-31)
03-30-2020, 10:23 PM
|
|
Replies: 18
Views: 8,360
Re: 7 tooth steering box
Ok, I am in the psocess of rebuilding my 7 tooth steering box. I was looking at the sector shaft. It is an undrilled replacement. Surprise as the sector housing wasn't drilled & tapped for a grease...
|
|
Forum: Model A (1928-31)
05-20-2019, 05:32 PM
|
|
Replies: 3
Views: 1,517
|
|
Forum: Model A (1928-31)
05-20-2019, 05:08 PM
|
|
Replies: 3
Views: 1,517
|
|
Forum: Model A (1928-31)
04-15-2019, 11:20 PM
|
|
Replies: 4
Views: 1,322
|
|
Forum: Model A (1928-31)
04-15-2019, 11:18 PM
|
|
Replies: 4
Views: 1,322
Re: backing plate bolts too long?
Thank you, to all. Ordered new backing plates. If they arrive w/ the raised collars that will work. If not I will use washers @ the bolt heads.
|
|
Forum: Model A (1928-31)
04-15-2019, 06:28 PM
|
|
Replies: 4
Views: 1,322
backing plate bolts too long?
Plan to use washers at the heads of backing plate bolts to take up length of bolts so castle nuts and bolt holes line up properly. Good idea?
|
|
Forum: Model A (1928-31)
05-18-2016, 02:55 PM
|
|
Replies: 9
Views: 2,954
|
|
Forum: Model A (1928-31)
05-16-2016, 09:03 PM
|
|
Replies: 9
Views: 2,954
Borg warner overdrive
OK, I hope this is the correct way to ask a question. I have Tom Endys article "Borg Warner overdrive". In it he provides a wiring diagram for the Model A Ford. I cannot figure out how to wire the...
|
|
Forum: Model A (1928-31)
05-16-2016, 12:37 AM
|
|
Replies: 2
Views: 2,024
Re: Borg Warner Overdrive schematic
i have your article on the recommended way to wire a borg warner overdrive to a Model A Ford. However I am unable to figure out how to connect the which wires to hook up to the headlight relay. I...
|
|
Forum: Questions & Suggestions
04-11-2012, 06:52 PM
|
|
Replies: 1
Views: 1,494
Right to left hand brake handle
Sirs, how involved will it be to convert to a left side brake handle from the right side set up i have now. Also would this be correct for my October,1928,coupe.
|
|
Forum: Model A (1928-31)
05-27-2011, 03:20 PM
|
|
Replies: 20
Views: 5,381
Re: install engine
I am having the same problem, unable to close 1/2" gap between trans and flywheel housings. Splines are in mesh to get this far, but can the clutch alignment/missalignment be the problem this far in?
|
