Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 19 of 19
Search took 0.00 seconds.
Search: Posts Made By: JAS1949
Forum: Early V8 (1932-53) 03-17-2021, 10:24 AM
Replies: 7
Views: 416
Posted By JAS1949
Re: Thread Size

Thanks Guys for all the info. Had the die in my box. Worked great. Another step forward. Thanks again.
Forum: Early V8 (1932-53) 03-16-2021, 09:30 AM
Replies: 7
Views: 416
Posted By JAS1949
Thread Size

Hi Again Guys, I have a 1937 steering box I'm installing on a 36. Rebuilding it now. 1st couple threads were smashed when I took the nut off the steering sector shaft it turned the threads bigger...
Forum: Early V8 (1932-53) 03-08-2021, 11:16 PM
Replies: 8
Views: 455
Posted By JAS1949
Re: Clutch/Brake Pedal Assembly

Thanks David, I can only dream, that my 36 will look as good as yours. But I keep on plugging away.
Forum: Early V8 (1932-53) 03-08-2021, 08:23 PM
Replies: 8
Views: 455
Posted By JAS1949
Re: Clutch/Brake Pedal Assembly

Thanks Guys. No I dont have the toe board installed. Frame off restoration. Couldn't find any other number on brake ar. Bends slightly to left then goes straight. I'll try and post a picture...
Forum: Early V8 (1932-53) 03-08-2021, 07:31 PM
Replies: 8
Views: 455
Posted By JAS1949
Clutch/Brake Pedal Assembly

Hi Guys, I need help. First time build. 36 roadster brake pedal hits frame when it returns. Don't think this is right. The brake arm only has a M3 on it. The clutch has 48-7520-A2. Are these the...
Forum: Early V8 (1932-53) 01-13-2019, 08:51 AM
Replies: 4
Views: 669
Posted By JAS1949
Re: Cam Bearings

Thanks guys I appreciate it.
Forum: Early V8 (1932-53) 01-12-2019, 04:57 PM
Replies: 4
Views: 669
Posted By JAS1949
Cam Bearings

Another newbie question. Ready to install new cam bearings, 1936 221ci. Does the big oil hole or small oil hole in the bearing , mate with the hole in the block?
Rear bearing only has 1 hole. ...
Forum: Early V8 (1932-53) 01-06-2019, 08:32 AM
Replies: 10
Views: 866
Posted By JAS1949
Re: Rod Bearings

Will do. Thanks to all.
Forum: Early V8 (1932-53) 01-06-2019, 08:10 AM
Replies: 10
Views: 866
Posted By JAS1949
Re: Rod Bearings

Sorry for the repeat. New at this.
Forum: Early V8 (1932-53) 01-06-2019, 08:08 AM
Replies: 10
Views: 866
Posted By JAS1949
Re: Rod Bearings

Thanks for all the help guys. I'm pretty finicky too. Got books recommended by guys on FordBarn. Just couldn't find .030 under/ standard bearings. Is it ok to use 3 different brands, pairs match, if...
Forum: Early V8 (1932-53) 01-06-2019, 07:57 AM
Replies: 10
Views: 866
Posted By JAS1949
Re: Rod Bearings

Thanks for all the help. I'm pretty finicky too. Got good books recommended by guys on FordBarn. Just couldn't find .030 under/ standards. Ron, who is Nax VP, cant find him.
Forum: Early V8 (1932-53) 01-05-2019, 12:44 PM
Replies: 10
Views: 866
Posted By JAS1949
Rod Bearings

New to the flathead scene. Anyone's help is appreciated. Engine has been rebuilt previously. Engine was balanced and sleeved. If I bore connecting rods to .010 over will that throw off the engine...
Forum: Early V8 (1932-53) 09-09-2011, 03:19 AM
Replies: 7
Views: 1,127
Posted By JAS1949
Re: 36 Front Axle

Any luck on 36 front end?
Forum: Early V8 (1932-53) 09-07-2011, 03:34 PM
Replies: 7
Views: 1,127
Posted By JAS1949
Re: 36 Front Axle

Thanks guys for your help. Now I need to know the measurement difference between a '36 & '37 up. Where do I measure & what's the measurements. Thanks Loads . I'm learning!!
Forum: Early V8 (1932-53) 09-06-2011, 04:09 PM
Replies: 7
Views: 1,127
Posted By JAS1949
36 Front Axle

Hi Guys, I,m new at this, bear with me. I've got a juiced axle 38 or 39, I guess. Is there any differences in measurements from this to a 1936.I noticed the perches are different, and the spindle...
Forum: Early V8 (1932-53) 05-18-2011, 06:51 AM
Replies: 3
Views: 994
Posted By JAS1949
Re: Identify Fenders

You guys are absolutely right. Checked em out. My Uncle must have done it right after WWII. I'm sure I'll be posting alot. Car is a basket case. Got all the parts, I THINK. Fenders are for sale....
Forum: Early V8 (1932-53) 05-17-2011, 08:12 PM
Replies: 3
Views: 994
Posted By JAS1949
Identify Fenders

HELP ME !! I'm new and I need to id these fenders. They were on my 36 roadster when I bought it. They are 2 pc. The 2nd pc. is were the bumper brace goes through. There is a very slight point along...
Forum: Questions & Suggestions 05-17-2011, 07:08 PM
Replies: 0
Views: 915
Posted By JAS1949
Unidentified fenders

HELP ME !! I'm new and I need to id these fenders. They were on my 36 roadster when I bought it. They are 2 pc. The 2nd pc. is were the bumper brace goes through. There is a very slight point along...
Forum: Early V8 04-27-2011, 03:24 PM
Replies: 1
Views: 773
Posted By JAS1949
Early Ford Gas Heaters & 38-39? Front Fenders

I have 6 early gas heaters. Housings aren't damaged, will probably need work to the electric portions. They need painting.4 South Wind & 2 ? Not Sure . Gray with red Stripes at Bottom. $50.00 ea. I...
Showing results 1 to 19 of 19

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:18 PM.