Forum: Model A (1928-31)
Today, 05:56 AM
|
|
Replies: 43
Views: 8,156
|
|
Forum: Model A (1928-31)
04-16-2024, 09:57 AM
|
|
Replies: 26
Views: 1,377
|
|
Forum: Model A (1928-31)
04-16-2024, 09:47 AM
|
|
Replies: 6
Views: 345
|
|
Forum: Model A (1928-31)
04-10-2024, 10:46 AM
|
|
Replies: 26
Views: 1,265
Re: Saw at the Old Car Festival 2023
nkaminar, your tag topper is unusual because it indicates that Wilkes is a state. I have a collection of many tag toppers, but none as rare as yours. Your topper is the first I have seen...
|
|
Forum: Model A (1928-31)
04-10-2024, 07:57 AM
|
|
Replies: 24
Views: 1,035
Re: A newbie needs help!
It is probable that the engine is not the car's original, so the engine number is a poor choice for a VIN. If you have an existing registration for the car, use the VIN on it. In my Model A's, I have...
|
|
Forum: Model A (1928-31)
04-09-2024, 10:01 AM
|
|
Replies: 14
Views: 734
|
|
Forum: Model A (1928-31)
04-09-2024, 09:50 AM
|
|
Replies: 5
Views: 532
|
|
Forum: Model A (1928-31)
04-08-2024, 08:03 AM
|
|
Replies: 14
Views: 734
Condenser Capacity
While researching V8 service bulletins for info pertaining to the Model "A,"I stumbled upon this chart of condenser capacities.
|
|
Forum: Model A (1928-31)
04-08-2024, 07:53 AM
|
|
Replies: 21
Views: 1,524
Re: How tight should the...
There needs to be some compression of the springs to enable the joint to take-up wear of the balls and cups, so the ball joints do not develop free play.
|
|
Forum: Model A (1928-31)
04-08-2024, 07:31 AM
|
|
Replies: 18
Views: 1,004
|
|
Forum: Model A (1928-31)
04-07-2024, 10:01 AM
|
|
Replies: 18
Views: 1,004
Differential Pinion Gear Bearing Preload
nkaminar in Post #3 is correct, the torques in the following service bulletins are the torques necessary to turn the pinion resulting from tightening the jam nuts. In other words, you tighten the jam...
|
|
Forum: Model A (1928-31)
04-07-2024, 09:32 AM
|
|
Replies: 21
Views: 1,524
Re: How tight should the...
I researched all of the Ford Service Bulletins 1928 through 1942 and there is no quantitative instruction about tightening the drag link and tie rod end plugs. I use the 25% spring compression...
|
|
Forum: Model A (1928-31)
04-05-2024, 09:57 AM
|
|
Replies: 24
Views: 1,364
Re: Oil Pump Shaft
Here is the Service Bulletin regarding the undercut oil pump shaft. There is a picture of B-6608 Undercut Shaft on Vince Falter's Ford Barn https://www.fordgarage.com/pages/boilpumpshaft.htm
|
|
Forum: Model A (1928-31)
04-05-2024, 07:25 AM
|
|
Replies: 8
Views: 723
Re: D Nut Hole Punch
Make templates from card-stock of the various size D-Nuts you need to install. Tape the template in place & use a marking pen to transfer the shape onto the body. Drill an under-size diameter hole...
|
|
Forum: Model A (1928-31)
04-02-2024, 08:00 AM
|
|
Replies: 4
Views: 690
Re: Dale Gosa has passed.
I am sorry to hear of Dale's passing, and I pray his soul is resting in peace in God's Kingdom of Heaven. Dale helped me many times with information to restore my Victoria. He will be missed.
|
|
Forum: Model A (1928-31)
04-02-2024, 07:56 AM
|
|
Replies: 24
Views: 1,364
Re: Oil Pump Shaft
See the Ford Service Bulletin of November 1932, Page 67. The Company indicates that the B-6608 Pump Shaft can be used in the Model A for improved oil flow. The B-6608 Shaft was the service...
|
|
Forum: Model A (1928-31)
04-02-2024, 07:43 AM
|
|
Replies: 16
Views: 921
|
|
Forum: Model A (1928-31)
04-02-2024, 07:39 AM
|
|
Replies: 15
Views: 867
|
|
Forum: Model A (1928-31)
04-02-2024, 07:36 AM
|
|
Replies: 21
Views: 1,524
|
|
Forum: Model A (1928-31)
04-02-2024, 07:33 AM
|
|
Replies: 15
Views: 928
|
|
Forum: Model A (1928-31)
04-01-2024, 10:13 AM
|
|
Replies: 16
Views: 921
Re: Universal Tires
Ed, the Model A Ford Club of Long Island to which I belong, has an annual front end alignment clinic that i attend. I have learned the hard way that low tire pressure increases front tire wear, and...
|
|
Forum: Model A (1928-31)
04-01-2024, 10:01 AM
|
|
Replies: 10
Views: 604
Re: Separator
Wow! I never thought about water getting into the gas tank from rain / the garden hose. Now that you mention it, I can understand water intrusion via the vent in the cap. I have had condensation...
|
|
Forum: Model A (1928-31)
04-01-2024, 09:46 AM
|
|
Replies: 17
Views: 918
Re: Reusing cluster gears
I have rebuilt and run several transmissions with used cluster gears. I have never bought / used a new cluster gear. To date, after thousands of miles, all is good using SAE 75W145 gear oil. A little...
|
|
Forum: Model A (1928-31)
04-01-2024, 09:38 AM
|
|
Replies: 24
Views: 1,364
Oil Pump Shaft
The Model "A" oil pump has a 5/8" diameter shaft A-6608. In 1932 - 1934, the B-6608 Oil Pump shaft is undercut to 9/16" diameter between its bushing locations to increase oil flow for the pressurized...
|
|
Forum: Model A (1928-31)
03-31-2024, 10:08 AM
|
|
Replies: 8
Views: 522
Re: Electrical Fuses
Thanks all for your guidance. Y-Blockhead, your panel is very nice setup. Thanks for sharing it. Katy, thanks for info about sizing fuses.
|
