Forum: Early V8 (1932-53)
Yesterday, 01:10 PM
|
Replies: 149
Views: 10,637
Re: 276 stroker from 35 years of parts
You always need to install the rear-main seal (in the block) before you put the crankshaft in. I prefer to use the graphite impregnated ones from BestGasket.
Question, did you wash the block with...
|
Forum: Early V8 (1932-53)
05-01-2024, 02:45 PM
|
Replies: 10
Views: 483
Re: Old brazed repairs on a 21 stud
Me, I'd probably grind down into the brass a bit and see how deep it goes. When there are cracks like that, you can almost be assured they go down into/below the hardened valve seat. The right...
|
Forum: Early V8 (1932-53)
04-30-2024, 06:53 AM
|
Replies: 13
Views: 662
|
Forum: Early V8 (1932-53)
04-30-2024, 06:51 AM
|
Replies: 19
Views: 574
Re: Help with a recent 8ba rebuild
You can do what was mentioned up above - to be sure your timing is correctly set . . . or you can explore other distributor options. Even with the initial timing set correctly, you'll still have an...
|
Forum: Early V8 (1932-53)
04-30-2024, 06:44 AM
|
Replies: 22
Views: 921
Re: Columbia two speed differentials
They are one of the few choices if you want to have an overdrive and not put a bunch of modern gear in an early car. With that said, they are expensive to buy and to get ready to use - but you'll...
|
Forum: Early V8 (1932-53)
04-29-2024, 06:14 PM
|
Replies: 25
Views: 840
|
Forum: Early V8 (1932-53)
04-28-2024, 01:46 PM
|
Replies: 149
Views: 10,637
Re: 276 stroker from 35 years of parts
Those valves are perfectly fine . . . carry on!
If you have a lathe, take some 800 grit black/carbide sandpaper and polish the stems. Or use a high-speed drill. ;)
Put some good...
|
Forum: Early V8 (1932-53)
04-28-2024, 11:33 AM
|
Replies: 149
Views: 10,637
Re: 276 stroker from 35 years of parts
Your seat width looks quite wide on the valve that was lapped. Are you doing multi-angle seats - such that you can control the width and placement of the 45 degree seat?
You want the seat further...
|
Forum: Early V8 (1932-53)
04-28-2024, 08:38 AM
|
Replies: 22
Views: 832
|
Forum: Early V8 (1932-53)
04-27-2024, 09:12 AM
|
Replies: 14
Views: 881
|
Forum: Early V8 (1932-53)
04-27-2024, 09:10 AM
|
Replies: 149
Views: 10,637
Re: 276 stroker from 35 years of parts
I bet that ole' cornhead grease would be just fine in your situation. You don't have much spring pressure, so you'll probably be just fine. I use a special lubrication that is designed for cams...
|
Forum: Early V8 (1932-53)
04-26-2024, 10:23 AM
|
Replies: 13
Views: 742
Re: Removing perch bolt for repair
Another thing to consider is using some big C-Clamps and then slowly disassembling the spring pack - such that only the main leaf is attached to the perches.
This usually takes the vast majority...
|
Forum: Early V8 (1932-53)
04-25-2024, 06:57 AM
|
Replies: 149
Views: 10,637
Re: 276 stroker from 35 years of parts
It is best to have an actual gear puller . . . if you use a 3-jaw you'll probably only get it onto the teeth and it is very easy to break them off. Ask me how I know such things! LOL
|
Forum: Early V8 (1932-53)
04-25-2024, 06:54 AM
|
Replies: 17
Views: 998
|
Forum: Early V8 (1932-53)
04-25-2024, 06:47 AM
|
Replies: 35
Views: 1,433
|
Forum: Early V8 (1932-53)
04-22-2024, 08:54 PM
|
Replies: 149
Views: 10,637
Re: 276 stroker from 35 years of parts
Since you're putting a new cam in the engine, you should consider having the bottoms of the lifters resurfaced as well. Pete on here can do that for you - I highly recommend having it done (is not...
|
Forum: Early V8 (1932-53)
04-22-2024, 01:49 PM
|
Replies: 19
Views: 1,427
Re: Compression and flow
The problem with a definitive answer is that the only one that is accurate is "it depends".
Having higher compression is a big benefit in a flathead for normal off-the-line performance, cruising a...
|
Forum: Early V8 (1932-53)
04-17-2024, 12:52 PM
|
Replies: 27
Views: 1,793
Re: Narrow V8 Rear Axle
We're on the same page . . . and I hope my recommendations of how to effectively modify a V8 style rear for width, added strength and the ability to use the brakes you have works for you.
Best...
|
Forum: Early V8 (1932-53)
04-17-2024, 07:33 AM
|
Replies: 72
Views: 27,023
Re: Isky 404A cam - Harley Davidson grind?
I've checked the double springs against the Isky 185-G springs and the 185-G springs are actually better. I have no idea as to why Ed created the dual-spring package . . . other than to claim it was...
|
Forum: Early V8 (1932-53)
04-16-2024, 08:12 AM
|
Replies: 24
Views: 1,349
Re: 8BA Flathead Ford Crankshaft Pulley Install
At least you can now sleep at night! Isn't it funny how we can start worrying about something like this . . . and it just plagues our mind until we go check it out and either see there is no problem...
|
Forum: Early V8 (1932-53)
04-16-2024, 08:09 AM
|
Replies: 50
Views: 1,967
Re: 91 birthday today
Happy Belated Birthday Ron! My Mom just turned 91 on the first . . . and like you, she is still a vibrant and wonderful person. Keep on moving . . . and get to 92!
|
Forum: Early V8 (1932-53)
04-16-2024, 08:07 AM
|
Replies: 11
Views: 1,125
|
Forum: Early V8 (1932-53)
04-15-2024, 12:19 PM
|
Replies: 11
Views: 1,125
|
Forum: Early V8 (1932-53)
04-15-2024, 12:17 PM
|
Replies: 24
Views: 1,349
Re: 8BA Flathead Ford Crankshaft Pulley Install
That big ole' bolt will take a lot more torque than 60 lbs - though the washer that goes with it may deflect. I would not worry about it in the least. If you're nervous, check it with a torque...
|
Forum: Early V8 (1932-53)
04-15-2024, 12:12 PM
|
Replies: 27
Views: 1,793
Re: Narrow V8 Rear Axle
Best solution: Banjo axle, updated with late 28 spline axles with a 5 x 5 1/2 bolt pattern, new axle bearing ends for using the Lincoln backing plates and brakes, modified differential and ring...
|