Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 79
Search took 0.01 seconds.
Search: Posts Made By: S.Duncan
Forum: Early V8 (1932-53) 07-14-2022, 09:20 PM
Replies: 4
Views: 309
Posted By S.Duncan
Re: Need a dimension;34 ford

Thats great,thank you
Forum: Early V8 (1932-53) 07-14-2022, 08:46 PM
Replies: 4
Views: 309
Posted By S.Duncan
Re: Need a dimension;34 ford

Thanks Digger I'm looking for a measurement on a stock 34 with a hood and a stock rad and firewall.
Forum: Early V8 (1932-53) 07-14-2022, 08:05 PM
Replies: 4
Views: 309
Posted By S.Duncan
Need a dimension;34 ford

I'm installing my recored stock 34 rad and the stay rods are new. I don't plan on running a hood for a while so I need a measurement from lip of the top of the firewall in the center to the back of...
Forum: Early V8 06-29-2022, 04:31 PM
Replies: 0
Views: 254
Posted By S.Duncan
354 gearset 18 tooth speedo turtle

Looking for 18 tooth speedo turtle for 354 gearset
Forum: Early V8 05-31-2022, 07:02 PM
Replies: 0
Views: 211
Posted By S.Duncan
Wanted;33-34 4 blade v8 fan

Found one,thanks
Forum: Early V8 03-27-2022, 01:56 PM
Replies: 0
Views: 231
Posted By S.Duncan
39 deluxe glovebox clock

Looking for presentable original 39 deluxe glovebox clock
Forum: Early V8 01-11-2022, 08:28 AM
Replies: 3
Views: 962
Posted By S.Duncan
Forum: Early V8 (1932-53) 09-25-2021, 03:00 PM
Replies: 12
Views: 1,446
Posted By S.Duncan
Forum: Early V8 06-08-2021, 12:03 PM
Replies: 0
Views: 246
Posted By S.Duncan
Wanted, ; 4 inch merc crank,close to standard

Wanted looking for a decent 4 inch merc crank not too rusty and close to standard. Hopefully in Southern Ontario
Forum: Early V8 (1932-53) 05-11-2021, 12:15 PM
Replies: 13
Views: 952
Posted By S.Duncan
Re: 35-36 rear into 34

Great, thats just the info I was looking for.
Forum: Early V8 (1932-53) 05-11-2021, 06:28 AM
Replies: 13
Views: 952
Posted By S.Duncan
Re: 35-36 rear into 34

Does anyone have a torque tube length measurement for a 35-40 rear into a 34 with a reshaped straight spring ?
Forum: Early V8 (1932-53) 05-10-2021, 01:46 PM
Replies: 13
Views: 952
Posted By S.Duncan
Re: 35-36 rear into 34

I've already had the 34 torque tube and driveshaft bolted up. The roll pin was even in the right place on the pinion. The torque tube needed to by relieved a bit to clear the later pinion bearing
Forum: Early V8 (1932-53) 05-10-2021, 09:03 AM
Replies: 13
Views: 952
Posted By S.Duncan
Re: 35-36 rear into 34

My 34 driveshaft and 36 pinion are both 10 spline
Forum: Early V8 (1932-53) 05-10-2021, 07:52 AM
Replies: 13
Views: 952
Posted By S.Duncan
35-36 rear into 34

I've been told in the past that a 35-40 rear with a reground spring will fit in a 33-4 using a stock 34 torque tube and driveshaft. I realize this moves the wheels back slightly, but that would only...
Forum: Early V8 03-01-2021, 10:08 AM
Replies: 3
Views: 962
Posted By S.Duncan
Forum: Model-A 03-01-2021, 10:08 AM
Replies: 1
Views: 814
Posted By S.Duncan
Forum: Early V8 03-01-2021, 10:07 AM
Replies: 0
Views: 203
Posted By S.Duncan
wanted for 39 conv. coupe

looking for conv. top mount/pivot castings which bolt to top of b pillars for 39 convertible coupe.
Forum: Early V8 (1932-53) 01-06-2021, 04:43 PM
Replies: 4
Views: 563
Posted By S.Duncan
Forum: Early V8 (1932-53) 01-06-2021, 02:07 PM
Replies: 4
Views: 563
Posted By S.Duncan
32 roadster body dimension

I'm in the process of piecing together my long term 32 roadster project. Like many original roadster bodies it was completely disassembled for rear floor and subframe work. I'm looking for an outside...
Forum: Model-A 10-19-2020, 02:32 PM
Replies: 1
Views: 814
Posted By S.Duncan
wanted 28-29 phaeton;need all 4 doors

wanted: i'm looking for all 4 doors for 28_29 phaeton.Must be half decent small patches needed okay.
Forum: Early V8 04-27-2019, 06:52 AM
Replies: 1
Views: 724
Posted By S.Duncan
Forum: Early V8 04-27-2019, 06:51 AM
Replies: 3
Views: 962
Posted By S.Duncan
Forum: Early V8 03-23-2019, 12:01 PM
Replies: 1
Views: 724
Posted By S.Duncan
34 ford garwood skirts

Looking for original garwood skirts for 33-34 ford
Forum: Early V8 03-23-2019, 11:59 AM
Replies: 3
Views: 962
Posted By S.Duncan
isky 404 cam drilling jig

looking for drilling jig and installation tools for Isky 404 radius lifters
Forum: Early V8 11-07-2018, 08:11 AM
Replies: 1
Views: 893
Posted By S.Duncan
Showing results 1 to 25 of 79

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:02 AM.