Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 17 of 17
Search took 0.00 seconds.
Search: Posts Made By: Randy Lausch
Forum: Model A (1928-31) 09-27-2021, 12:26 PM
Replies: 1
Views: 229
Posted By Randy Lausch
Exhaust valves

Some of my exhaust valves are running .012 the book says they should be .015 is .012 close enough or should I have the valve stems ground down. If so what kind of grinder will I need. Some where I...
Forum: Model A (1928-31) 09-26-2021, 08:56 AM
Replies: 3
Views: 438
Posted By Randy Lausch
Valves

Some of my exhaust valves are running .012 do you think that is close enough or shouldI have the valve stems ground down. If I need to what kind of grinder can I buy to do that
Forum: Model A (1928-31) 09-03-2021, 05:20 PM
Replies: 8
Views: 840
Posted By Randy Lausch
Diamond block engine

Can anyone tell me the difference between a model A 4 cylinder flathead & a diamond engine. I found a diamond engine & tore the oil pan off & they both look the same to me
Forum: Questions & Suggestions 09-03-2021, 05:12 PM
Replies: 1
Views: 190
Posted By Randy Lausch
Diamond engine

Can anyone tell me what the difference between a model A 4 cylinder flathead & a diamond 4 cylinder flathead. I found one & I tore it down & I canít tell the difference between the two. They look...
Forum: Model A (1928-31) 08-29-2021, 08:40 AM
Replies: 6
Views: 518
Posted By Randy Lausch
Where did my compression go

I have a motor that ran very good, we have let it sit for several years now there is no compression in any of the cylinders. Is there any thing I can add to the cylinders I assume it has to be the...
Forum: Model A (1928-31) 08-18-2021, 05:49 PM
Replies: 6
Views: 635
Posted By Randy Lausch
Re: Water in intake ports

How do I pressure check it
Forum: Model A (1928-31) 08-18-2021, 12:17 PM
Replies: 6
Views: 635
Posted By Randy Lausch
Water in intake ports

I pulled the intake off I noticed there was water in both intake ports. So I assume I may have a blown head gasket. I milled the head & put a new head gasket on, & I still have water in the intake...
Forum: Model A (1928-31) 08-11-2021, 10:55 AM
Replies: 3
Views: 492
Posted By Randy Lausch
Two tooth gear box

On a two tooth gear box how do you get the shaft to pull out of the worm gear. I thought about heating it up but I donít know if thatís good for the worm gear thanks Randy
Forum: Model A (1928-31) 08-07-2021, 08:00 AM
Replies: 15
Views: 1,058
Posted By Randy Lausch
Valve clearance

Putting a new head gasket on a 4 cylinder Model A I decided to check the valve clearance . Two of the intake valves had 8000 clearance, I wonder if anyone knows how critical that clearance is. I...
Forum: Model A (1928-31) 08-04-2021, 04:21 PM
Replies: 3
Views: 541
Posted By Randy Lausch
Re: Michigan Model A ROUND UP

No someone who sells new parts
Forum: Model A (1928-31) 08-04-2021, 12:57 PM
Replies: 3
Views: 541
Posted By Randy Lausch
Michigan Model A ROUND UP

Do you guys know of any new Model A part dealers that are going to Auburn Hills mi. I believe itís north of Detroit
Forum: Model A (1928-31) 08-02-2021, 10:50 AM
Replies: 3
Views: 580
Posted By Randy Lausch
What kind of frame do I have

I have a frame that appears to be about 116 inches long. The guy I bought it from said he thought it was a model A coupe frame. I want to start to put a body on it , can anyone tell me 100% sure it...
Forum: Model A (1928-31) 07-24-2021, 12:37 PM
Replies: 9
Views: 965
Posted By Randy Lausch
Re: What model A would this be

Star A x318159 star
Forum: Model A (1928-31) 07-24-2021, 10:49 AM
Replies: 9
Views: 965
Posted By Randy Lausch
What model A would this be

Found this number on my frame, has a star, then ax3 8159 . Iím not 100% sure the 3 is a 3
Forum: Model A (1928-31) 07-11-2021, 12:06 PM
Replies: 4
Views: 585
Posted By Randy Lausch
Setting carberator float

Does anybody know how to set the floats on a Tellison and a marvel all state carb and do they bend them or do they add washers to the float valve and the measurements of the floats.
Forum: Model A (1928-31) 06-06-2021, 11:26 AM
Replies: 2
Views: 403
Posted By Randy Lausch
model A

does anyone know if any of the new part dealers are going to be at the Gilmore Model A show in sept.
Forum: Model A (1928-31) 06-06-2021, 07:30 AM
Replies: 3
Views: 572
Posted By Randy Lausch
model A

when you torque down the rods to 35 lb. the cotterpin will not line up with the king nut. the only way i can get it is to over torque it sometimes it takes 45 lb. torque to get it to line up. or I...
Showing results 1 to 17 of 17

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:41 PM.