Forum: Early V8 (1932-53)
08-14-2012, 05:40 AM
|
Replies: 3
Views: 1,124
Re: Engine bolts
Lol, no, it's a 1935 model 51, i have a 48 V8 flathead though. thanks for the info will check it out.
|
Forum: Early V8 (1932-53)
08-14-2012, 03:29 AM
|
Replies: 3
Views: 1,124
Engine bolts
I have a 1935 Ford model 51 V8. Where can I get a set of bolts to mount the engine to the bell houseing? Also, should there be a gasket between them? I have not been able to find one for sale. Thanks
|
Forum: Early V8 (1932-53)
07-01-2012, 08:21 PM
|
Replies: 11
Views: 14,351
Re: Split rims
Thanks for the info. Will keep on searching for a place that does them.
|
Forum: Early V8 (1932-53)
07-01-2012, 05:10 PM
|
Replies: 11
Views: 14,351
Split rims
I have 20" rims on my Ford model 51. How dangerous is it to change the tires? Is there any secrets to make it safer?
|
Forum: Early V8 (1932-53)
06-20-2012, 10:56 PM
|
Replies: 10
Views: 1,658
|
Forum: Early V8 (1932-53)
06-20-2012, 12:29 AM
|
Replies: 10
Views: 1,658
Re: 35 Ford truck windshield question
Have the frame out. Soaked the four screws and they are stuck. Tomorrow will have to try some heat then the drill. Do all four screws have to come out on both sides to split the frame or can two on...
|
Forum: Early V8 (1932-53)
05-23-2012, 08:20 PM
|
Replies: 10
Views: 1,658
|
Forum: Early V8 (1932-53)
05-23-2012, 02:43 PM
|
Replies: 10
Views: 1,658
|
Forum: Early V8 (1932-53)
05-23-2012, 02:01 PM
|
Replies: 10
Views: 1,658
|
Forum: Early V8
04-02-2012, 10:06 AM
|
Replies: 0
Views: 978
1935 Ford Seats
Looking for seats for a 1935 Ford truck. Need to bench and back rest. Will take complete seats or springs.
|
Forum: Early V8 (1932-53)
03-17-2012, 07:43 PM
|
Replies: 10
Views: 1,794
Re: Engine year?
Sweet. Thanks for the info. I want the enigine in when I get home on leave.
|
Forum: Early V8 (1932-53)
03-17-2012, 06:46 PM
|
Replies: 10
Views: 1,794
Re: Engine year?
How do I post pics? Will try and get some of the motor. In Afghanistan right now.
|
Forum: Early V8 (1932-53)
03-17-2012, 10:56 AM
|
Replies: 10
Views: 1,794
|
Forum: Early V8 (1932-53)
03-17-2012, 10:27 AM
|
Replies: 10
Views: 1,794
Re: Engine year?
It's the model 51, 1 1/2 ton. So this would have a 3 speed? Only asking cause I don't know much about these and the company I bought it form said it had a 4 speed.
|
Forum: Early V8 (1932-53)
03-17-2012, 05:56 AM
|
Replies: 10
Views: 1,794
Engine year?
I have a Ford V8 flathead I want to put in my 1935 Ford model 51. The heads are marked 59 AB and have the cooling hose mounts/holes in the middle of the heads. The bell housing has a 59 raised on it....
|
Forum: Early V8 (1932-53)
03-12-2012, 11:29 PM
|
Replies: 1
Views: 1,106
Engine bolts
I have a 35' Ford model 51 truck. I purchased a 1948 V8 flathead to put in it. I never had the bolts to install it with. Does it need special bolts or will it be ok to use hardened bolts from the...
|
Forum: Early V8 (1932-53)
12-06-2011, 11:50 AM
|
Replies: 1
Views: 1,120
1935 Model 51 tires?
Stock on this truck are 6.50x20's in the front and 7.50x20's in the rear(dualies). Do I need to keep this same arrangement or can I run 6.50x20's in the rear as well?
|
Forum: Early V8 (1932-53)
09-23-2011, 09:27 AM
|
Replies: 5
Views: 1,224
|
Forum: Early V8 (1932-53)
09-20-2011, 02:38 AM
|
Replies: 20
Views: 3,905
Re: Questions
Ok, relooked at the motor. The block has a raised 59 above the flywheel and the heads say 59 A-B. Can't get picks to attach. Are these stronger motors than the earlier models? I looked at the oil pan...
|
Forum: Early V8 (1932-53)
09-19-2011, 10:45 PM
|
Replies: 5
Views: 1,224
Model 51 floor
Anyone have a picture of the interior floor? Trying to see the transmission cover and piece on the toe board around the steering column and pedals. Thanks
|
Forum: Early V8 (1932-53)
09-16-2011, 06:49 PM
|
Replies: 20
Views: 3,905
Re: Questions
Can't find it, can you please link it for me. THanks, Will have more info and try and post a pic when I get in from the field. Thanks
|
Forum: Early V8 (1932-53)
09-15-2011, 12:29 AM
|
Replies: 20
Views: 3,905
|
Forum: Early V8 (1932-53)
09-14-2011, 07:17 PM
|
Replies: 20
Views: 3,905
|
Forum: Early V8 (1932-53)
09-14-2011, 10:21 AM
|
Replies: 20
Views: 3,905
Re: Questions
The engine is marked 59 A-B and it has the crab distributer behind the fan blade on the front of the block.
|
Forum: Early V8 (1932-53)
09-14-2011, 02:41 AM
|
Replies: 20
Views: 3,905
Questions
I have a 24 stud 48' egine I want to put in my 35' Model 51.
What oil is recomended to put in and weight?
This has the short oil pan that does not cover the clutch/flywheel, what do you...
|