Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 96
Search took 0.01 seconds.
Search: Posts Made By: cvicky
Forum: Late V8 06-20-2021, 06:55 AM
Replies: 0
Views: 429
Posted By cvicky
gas door licience holder

wanted gas door licience holder 55 fairlane
Forum: Late V8 (1954+) 06-17-2021, 12:31 PM
Replies: 1
Views: 417
Posted By cvicky
white plugs black tail pipes

plugs have all been consistently white for last 5 yrs
car starts great cold , when i stop 5-10 minutes starts good ,but 20 minutes it will crank a bit before starting

the other thing i forgot to...
Forum: Late V8 (1954+) 05-22-2021, 04:08 PM
Replies: 7
Views: 853
Posted By cvicky
y block to rich

leaned out the float still running rich
plugs are white tailpipes are black still cranks a lot when warm but will eventually start
Forum: Late V8 (1954+) 05-08-2021, 01:05 PM
Replies: 11
Views: 1,611
Posted By cvicky
Re: manual three spd trans

here's a picture....
Forum: Late V8 (1954+) 05-05-2021, 07:32 PM
Replies: 11
Views: 1,611
Posted By cvicky
Re: manual three spd trans

yes its AB-7222-B and the tail AB7651-A and the side cover is sqare
Forum: Late V8 (1954+) 05-04-2021, 09:48 AM
Replies: 4
Views: 741
Posted By cvicky
Re: Transmission ID

i have same in my 55 crown AB-7222-B and AB-7651-A it seems to be leaking from the front shaft but its hard to tell with clutch and flywheel draft
let me know what you find out
Forum: Late V8 (1954+) 04-29-2021, 06:51 AM
Replies: 8
Views: 605
Posted By cvicky
Re: windshield leak

old seal but very nice shape
Forum: Late V8 (1954+) 04-28-2021, 06:50 PM
Replies: 11
Views: 1,611
Posted By cvicky
manual three spd trans

the number on the side is AB-1222-B 0 5
61 U i want to buy seals , is this a truck trans and or what year
Forum: Late V8 (1954+) 04-28-2021, 06:36 PM
Replies: 8
Views: 605
Posted By cvicky
windshield leak

windshield started leaking this year between where the glass sits in the rubber
hope i don't have to re/re
Forum: Late V8 (1954+) 11-13-2020, 09:16 PM
Replies: 16
Views: 1,849
Posted By cvicky
Re: oil bath conversion

4 brl T pot holey
Forum: Late V8 (1954+) 11-13-2020, 12:48 PM
Replies: 16
Views: 1,849
Posted By cvicky
oil bath conversion

i want to cut inside of breather and put paper filter
55 fairlane 272
anyone know which fram air filter fits
Forum: Late V8 (1954+) 11-13-2020, 12:42 PM
Replies: 6
Views: 807
Posted By cvicky
Re: 55 y block 272

how many miles do they have to be readjusted
Forum: Late V8 (1954+) 11-11-2020, 08:33 PM
Replies: 6
Views: 807
Posted By cvicky
55 y block 272

is it hydrolic lifters or solid
Forum: Late V8 (1954+) 11-11-2020, 08:31 PM
Replies: 7
Views: 1,077
Posted By cvicky
Re: driveshaft yoke

yes measured with rear axle on stands
Forum: Late V8 (1954+) 11-11-2020, 08:11 PM
Replies: 20
Views: 2,704
Posted By cvicky
Re: Pertronix Coil

flame thrower coil works ok laying down on my y block intake
pertronix ignitor failed when it was new so they had me cut wires and send them photo , they replaced N C
Forum: Late V8 (1954+) 10-29-2020, 10:30 AM
Replies: 7
Views: 1,077
Posted By cvicky
Re: driveshaft yoke

Mr driveshaft will modify my shaft
he says the slip yoke only needs enough play to get rear U joint in.
1/2 - 1"
Forum: Late V8 (1954+) 10-20-2020, 06:57 AM
Replies: 7
Views: 1,077
Posted By cvicky
driveshaft yoke

proper drive shaft length
it appears less than 1/4 of yoke is in back of trans one inch on splines
lots of up and down play but doesn't leak
Forum: Late V8 (1954+) 10-17-2020, 08:29 AM
Replies: 5
Views: 943
Posted By cvicky
Re: wiper arm and pivot 55 crown vic

my problem is my pivot is smaller than the hole in the arm
pivot 0.537 arm hole 0.549
when i turn electric wipers on wiper don't move
pivot is spinning in arm
Forum: Late V8 (1954+) 10-16-2020, 10:13 AM
Replies: 5
Views: 943
Posted By cvicky
wiper arm and pivot 55 crown vic

my wiper pivot measures 0.537 and my wiper arm 0.549 way to big
mine looks like MACS 17526-062 generic
also MACS says there is 4 different arms for 55-56
MACS also shows 6 7/16 and 6 1/4 for...
Forum: Late V8 (1954+) 10-12-2020, 03:31 PM
Replies: 23
Views: 2,212
Posted By cvicky
Re: vibration

yes new timing chain and gears
i set timing by vacuum engine runs best but light shows 20-25
ill do piston stop when i get a chance
i have another intake just have to make time
Forum: Late V8 (1954+) 10-12-2020, 03:23 PM
Replies: 23
Views: 2,212
Posted By cvicky
Re: vibration

no i cant break flake off
Forum: Late V8 (1954+) 10-12-2020, 08:26 AM
Replies: 23
Views: 2,212
Posted By cvicky
Re: vibration

top right hole the black is a piece of metal flaking off the size of a potato chip
Forum: Late V8 (1954+) 10-12-2020, 08:14 AM
Replies: 23
Views: 2,212
Posted By cvicky
Re: vibration

put timing light on 8 wires all good
took fan belt off no change
engine and trans mounts seem nice and rubbery with crowbar
exhaust is not touching any where
damper seems nice but timing...
Forum: Late V8 (1954+) 10-10-2020, 11:35 AM
Replies: 23
Views: 2,212
Posted By cvicky
Re: vibration

how do you check motor mounts
they are not broken but can they dry up
and how about the front by the rad
Forum: Late V8 (1954+) 10-06-2020, 07:59 AM
Replies: 23
Views: 2,212
Posted By cvicky
Re: vibration

i had damper off when i changed timing chain ,looked OK

what difference will a 240 / 300 flywheel make
Showing results 1 to 25 of 96

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:00 PM.