Forum: Early V8 (1932-53)
08-01-2023, 11:22 AM
|
|
Replies: 7
Views: 676
|
|
Forum: Early V8 (1932-53)
07-31-2023, 11:57 AM
|
|
Replies: 7
Views: 676
59A adjustable lifters having wear problem
Valves were getting increasingly noisy. When re-adjusting lifters, found some
had uneven wear. Turning lifter in the bore would yield a different reading. More than 10 thousandths in some...
|
|
Forum: Early V8 (1932-53)
05-22-2022, 03:52 PM
|
|
Replies: 11
Views: 1,403
|
|
Forum: Early V8 (1932-53)
05-19-2022, 11:33 AM
|
|
Replies: 11
Views: 1,403
|
|
Forum: Early V8 (1932-53)
05-16-2022, 08:11 PM
|
|
Replies: 11
Views: 1,403
|
|
Forum: Early V8 (1932-53)
05-16-2022, 07:13 PM
|
|
Replies: 11
Views: 1,403
Re: Crab Distibutor Vacuum brake pad gone
Well thanks guys. Punched a leather piece one size bigger and pressed it in. Tight fit this time. Learn something new every day. Now to just pull the distributor and remove the old pad. Jim
|
|
Forum: Early V8 (1932-53)
05-16-2022, 06:46 PM
|
|
Replies: 11
Views: 1,403
Re: Crab Distibutor Vacuum brake pad gone
Thanks for the responses guys...I did the same, bought 1/4 inch heavy leather and then punched the proper size. I know the leather kinda just set in there and i just glued it in. Worked just fine...
|
|
Forum: Early V8 (1932-53)
05-16-2022, 02:57 PM
|
|
Replies: 11
Views: 1,403
Crab Distibutor Vacuum brake pad gone
I want to glue a new leather pad on the vacuum brake plunger. What is the best glue. Cant remember what i used last time, but the leather fell off after only about 3000 miles. thanks for any help
|
|
Forum: Late V8 (1954+)
04-25-2020, 11:46 AM
|
|
Replies: 9
Views: 1,476
Re: Tranny shipping box
If you end up shipping with Fastenal, they may require something they can fork lift. I used an old pallet that i cut up to size. U might check on their requirements before u make a box. I just...
|
|
Forum: Late V8
03-17-2017, 03:24 PM
|
|
Replies: 0
Views: 906
HORNS 6Volt
$50 includes shipping to lower 48....Good sounding pair of Hi-Lo horns from a 54 Ford...6V..Nice and straight. Just needs a bead-blast and paint...Contact me by my email only.... [email protected]
|
|
Forum: Late V8
11-03-2016, 01:42 PM
|
|
Replies: 0
Views: 661
fordomatic and FMX transmissions
50 Bucks for each. Fordomatic came out of my 54 and shifted fine. Leaks oil a bit. Also have a FMX out of a 78? ford. These are being sold as cores, as I cant guarantee they work. FMX supposed to...
|
|
Forum: Late V8 (1954+)
10-01-2016, 12:19 PM
|
|
Replies: 1
Views: 1,338
|
|
Forum: Late V8
09-30-2016, 11:29 AM
|
|
Replies: 0
Views: 837
|
|
Forum: Early V8 (1932-53)
12-17-2013, 01:15 PM
|
|
Replies: 40
Views: 19,516
|
|
Forum: Model-A
10-13-2012, 11:09 AM
|
|
Replies: 0
Views: 868
Top Wood used, but serviceable
1930 Standard Coupe. Its all there. Not sure if its original, but i think it is, accept for the header, which is kinda funky. I would say header needs replacing and the side rails are partly gone...
|
|
Forum: Early V8
12-15-2011, 03:02 PM
|
|
Replies: 0
Views: 1,184
|
|
Forum: Early V8
12-15-2011, 02:54 PM
|
|
Replies: 0
Views: 979
Coil and Ign. resistor New
New Made in USA HOLLEY coil $45 and $5 for shipping in lower 48
6volt
Also ignition resistor for 32-48 $10 and free shipping
Both for 50 + 5 for shipping
Both never installed
To...
|
|
Forum: Early V8
10-18-2011, 11:19 AM
|
|
Replies: 2
Views: 1,241
|
|
Forum: Early V8
10-03-2011, 09:04 PM
|
|
Replies: 2
Views: 1,241
Flathead V8 Ignition parts
6v coil $45,
Plug wires $40,
ballast resistor $5,
Dist cap $20, SOLD
Rotor $5, SOLD
Dist contact plate $30, SOLD
Wire seals$10. SOLD
Fuel Pump SOLD
Senders SOLD
|
|
Forum: Early V8
09-05-2011, 11:30 AM
|
|
Replies: 0
Views: 1,017
|
|
Forum: Early V8
07-31-2011, 12:38 PM
|
|
Replies: 0
Views: 673
Distributor Parts New
New parts never installed. Shipping to be determined. You can PM me, but would rather email [email protected] .. Parts include Cap, seals, contact plate with cork seal, and rotor for 60 bucks. ...
|
|
Forum: Early V8
07-18-2011, 06:56 PM
|
|
Replies: 2
Views: 1,077
|
|
Forum: Early V8
07-17-2011, 09:21 PM
|
|
Replies: 2
Views: 1,077
Oil Pressure sender
SOLD brand new, never installed. 80 lb rated. Check it out at Sacromento vintage for particulars. P/N 05480. Includes hook-up wire. Flathead v8. actual shipping.
Contact me at...
|
|
Forum: Early V8 (1932-53)
05-19-2011, 10:31 PM
|
|
Replies: 3
Views: 1,587
|
|
Forum: Model A (1928-31)
03-01-2011, 08:09 PM
|
|
Replies: 17
Views: 6,167
|
