Forum: Model A (1928-31)
04-18-2021, 01:17 PM
|
|
Replies: 8
Views: 426
Re: Upcoming Swap Meet in Tulare, CA
We will be there, managed to get rooms, I have been locked up since March last year, the map was helpful showing where the pre-war stuff is and will certainly save me some walking, Amen.
|
|
Forum: Model-A
04-17-2021, 01:45 PM
|
|
Replies: 5
Views: 1,370
|
|
Forum: Model-A
04-04-2021, 01:20 PM
|
|
Replies: 4
Views: 2,186
|
|
Forum: Model-A
04-04-2021, 01:18 PM
|
|
Replies: 4
Views: 1,228
|
|
Forum: Model-A
04-04-2021, 01:17 PM
|
|
Replies: 9
Views: 2,151
|
|
Forum: Model-A
02-07-2021, 01:01 PM
|
|
Replies: 1
Views: 449
|
|
Forum: Model-A
01-13-2021, 03:53 PM
|
|
Replies: 1
Views: 449
Brierley Camshaft
Looking for a Brierley camshaft, the touring cam he does, I would like the cam bearing sizes, and a picture would be welcomed, btreserdern@sn.rr.com.
Thanks in advance.
|
|
Forum: Model A (1928-31)
10-07-2020, 12:23 PM
|
|
Replies: 121
Views: 110,867
|
|
Forum: Model A (1928-31)
05-03-2020, 02:25 PM
|
|
Replies: 7
Views: 1,779
Re: help with modern valve guides
The OP has the modern valve kit, Snyders A 6505 M, which have the one piece guides, they push in from the bottom and the spring holds them in place, if you use the hammer in guides then you would...
|
|
Forum: Model A (1928-31)
04-15-2020, 12:01 PM
|
|
Replies: 8
Views: 1,161
Re: 1931 engine blocks
I used Plucks study for a re stamped block and it placed it between March and September 1930.
|
|
Forum: Model A (1928-31)
03-08-2020, 06:22 PM
|
|
Replies: 4
Views: 878
|
|
Forum: Model A (1928-31)
03-08-2020, 06:21 PM
|
|
Replies: 4
Views: 878
Re: Oil filter Question
Yes I got that sorted out, I was looking for the small stubby filters, should I refit my Vortex manifold, which needs clearance with the front carb and filter, the filter specs do not always quote...
|
|
Forum: Model A (1928-31)
03-07-2020, 12:44 PM
|
|
Replies: 4
Views: 878
Oil filter Question
I have a oil filter mount that fits on the timing cover, the filter stud is 3/4, I am looking for a stud that is 3/4 to 13/16 to mount the filter which is 13/16, any know where I may find one, Thanks.
|
|
Forum: Model A (1928-31)
03-06-2020, 01:06 PM
|
|
Replies: 10
Views: 867
Re: Excessive right front tire wear?
Yes you can have more toe in on one side than the other, in my case it was a bent left steering arm causing the right front wheel to turn to far scrubbing the tire, take a look at the gap of the tie...
|
|
Forum: Model A (1928-31)
02-26-2020, 04:18 PM
|
|
Replies: 7
Views: 791
|
|
Forum: Model A (1928-31)
02-18-2020, 11:33 PM
|
|
Replies: 10
Views: 1,076
Re: Switching Engine, Reusing Flywheel
Has you stated you just replaced the clutch parts recently , the middle picture shows that, if this assembly with the flywheel was working fine with no chatter why replace it, make sure there is no...
|
|
Forum: Model A (1928-31)
02-01-2020, 04:06 PM
|
|
Replies: 13
Views: 2,268
Re: automatic transmisson
Hi Glenn,
John LaVoy of Model A Times installed a Ford A4LD with OD from a Ford ranger truck and was very happy with it, if you do a search you will find several others have installed various auto...
|
|
Forum: Model A (1928-31)
01-30-2020, 08:18 PM
|
|
Replies: 11
Views: 1,458
Re: Different front spindles?
In picture 1 I see a rust colored object, could this maybe holding the bearing out from where the bearing seats, what is it ?. You can see where the grease as made a mark but not where the above...
|
|
Forum: Model A (1928-31)
01-20-2020, 01:19 PM
|
|
Replies: 7
Views: 1,291
|
|
Forum: Model A (1928-31)
01-17-2020, 03:30 PM
|
|
Replies: 21
Views: 2,130
Re: steering sector
I have yet to hear of any poorly made 7 tooth parts, there are only 2 adjustments to make, there are shims in the lower housing to remove the play in the bearings top and bottom of the worm gear, the...
|
|
Forum: Model A (1928-31)
01-17-2020, 02:05 PM
|
|
Replies: 24
Views: 2,142
Re: Throttle shaft brass plug for zenith carbs
I don't think so, there is seldom any wear on that side of the shaft, I have
2 Zeniths hanging up that do not have them, I believe the plug would only be removed if the bushings have been replaced...
|
|
Forum: Model A (1928-31)
01-15-2020, 01:08 PM
|
|
Replies: 21
Views: 2,130
Re: steering sector
The first thing I would do is make sure the pitman arm bolt is tight, it takes a lot of torqueing to make that clamp close up, if that doesn't fix it then I would recheck all the measurements in the...
|
|
Forum: Model A (1928-31)
01-13-2020, 03:24 PM
|
|
Replies: 630
Views: 285,860
|
|
Forum: Model-A
01-08-2020, 01:57 PM
|
|
Replies: 8
Views: 2,354
|
|
Forum: Model-A
12-30-2019, 02:31 PM
|
|
Replies: 3
Views: 848
|
