Forum: Early V8 (1932-53)
Today, 12:53 PM
|
Replies: 8
Views: 413
|
Forum: Early V8
03-25-2024, 12:37 PM
|
Replies: 0
Views: 48
T5 To Flathead Conversion Kit
T5 to Flathead Transmission conversion kit for either the 85-92 or 93 up S10 T5 2 wheel drive transmission. Kit fits either the early or late blocks (late blocks need the stamped steel or cast iron...
|
Forum: Early V8
03-25-2024, 12:26 PM
|
Replies: 0
Views: 46
Winters Steel Belled V8 Quickchange
New Winters Steel Belled V8 Quick Change open drive rear end. 3.78 ring and pinion with wedge lock differential. Base rear includes as cast V8 center with Winters 31 spline axles (choice of B P) and...
|
Forum: Early V8
03-25-2024, 12:15 PM
|
Replies: 0
Views: 42
Winters V8 Center
New Winters V8 Quick Change Open Drive Center starting at $1725. Includes 4.11 ring and pinion, pinion installed, Bearing, Gaskets, One set of spur gears. Uses your early Ford rear end parts (side...
|
Forum: Early V8
03-25-2024, 12:07 PM
|
Replies: 81
Views: 6,701
|
Forum: Early V8
03-25-2024, 12:06 PM
|
Replies: 85
Views: 7,549
|
Forum: Early V8 (1932-53)
03-22-2024, 09:21 AM
|
Replies: 4
Views: 282
Re: 1933 Ford Truck Invoice
COD. Ford was gonna get paid. Times were tough back then. That's about the time my great uncles Cane Ford went broke. A little earlier in an effort to sell product in 1931 they offered a Model A...
|
Forum: Model A (1928-31)
03-10-2024, 02:32 PM
|
Replies: 16
Views: 1,102
Re: Donovan 4 Cylinder
I'm guessing if you could find the parts today it cost upwards of $50K+ to build the motor?
|
Forum: Early V8 (1932-53)
03-09-2024, 09:41 PM
|
Replies: 8
Views: 658
Re: 1932 b400
The car in Ziggsters photos is also in an ad on the HAMB run by a man in Canada. Best offer over $75K. Says it's in MacGregor? Walter Kowalsky the guy that converts a deuce sedan into a B400 clone....
|
Forum: Model A (1928-31)
03-08-2024, 06:30 PM
|
Replies: 16
Views: 1,102
Donovan 4 Cylinder
Studying the Donovan Aluminum 4 cylinder motor. I'm a rookie and am wondering what do they use for a head? They show both Flathead & Overhead parts. They are priced the same just 2 separate lists....
|
Forum: Early V8 (1932-53)
03-08-2024, 03:46 PM
|
Replies: 6
Views: 257
Re: 32 firewall differences?
I've had a bunch. I always was told the one in the red primer was an early? and the other one came a little later.
|
Forum: Early V8 (1932-53)
03-08-2024, 02:01 PM
|
Replies: 34
Views: 1,912
Re: Cadillac 331 in a Ford
Offenhauser used to a good source but since the family sold the business the new owners are not the best at running the business. Availability of parts has diminished and prices have increased...
|
Forum: Early V8 (1932-53)
03-08-2024, 01:17 PM
|
Replies: 34
Views: 1,912
Re: Cadillac 331 in a Ford
Several years ago if my memory is right I saw one of these conversions in AZ. I think it may have been owned by Jackie Howerton? Nice green 40 with patina.
|
Forum: Early V8 (1932-53)
03-07-2024, 11:13 AM
|
Replies: 18
Views: 925
Re: Help aligning body panels?
Really like my 40 standard coupe and everything sheet metal wise is good except for that pesky right rear hood corner being a little high. The bottom edge of the hood going forward is against the...
|
Forum: Early V8
03-07-2024, 06:35 AM
|
Replies: 16
Views: 1,068
|
Forum: Early V8
03-07-2024, 06:34 AM
|
Replies: 29
Views: 2,225
|
Forum: Early V8
03-07-2024, 06:33 AM
|
Replies: 28
Views: 1,478
|
Forum: Early V8
03-07-2024, 06:33 AM
|
Replies: 20
Views: 1,071
|
Forum: Early V8
03-07-2024, 06:32 AM
|
Replies: 13
Views: 705
|
Forum: Early V8
03-04-2024, 11:12 AM
|
Replies: 91
Views: 10,134
|
Forum: Early V8
03-04-2024, 11:12 AM
|
Replies: 21
Views: 946
|
Forum: Early V8
03-04-2024, 11:11 AM
|
Replies: 21
Views: 943
|
Forum: Early V8
03-04-2024, 11:10 AM
|
Replies: 81
Views: 6,701
|
Forum: Early V8
03-04-2024, 11:10 AM
|
Replies: 85
Views: 7,549
|
Forum: Early V8 (1932-53)
03-04-2024, 12:46 AM
|
Replies: 2
Views: 343
Re: 32 Speedo Shot Craps
Contacted Rusty, will send it to him this week for examination. It was working perfect after he repaired it. Something may have came loose? May need a replacement?
|