Forum: Model A (1928-31)
04-15-2024, 07:01 PM
|
Replies: 2
Views: 366
Re: Rear backing plate order of assembly
Thanks JayJay. This was the key element that I needed "Add backing plates using the two rear (short) bolts, loosely tightened" to know first step. Thanks very much for your thoughtful response. ...
|
Forum: Early V8
04-13-2024, 09:28 PM
|
Replies: 0
Views: 99
|
Forum: Model A (1928-31)
04-13-2024, 08:47 PM
|
Replies: 2
Views: 366
Rear backing plate order of assembly
Gents
Please advise the best order of assembly.
I had rear brakes/backing plates rebuilt by Randy Gross - great job and amazingly fast turnaround! Thanks Randy.
So now I have the rear...
|
Forum: Model A (1928-31)
07-22-2023, 05:08 PM
|
Replies: 9
Views: 1,211
|
Forum: Model A (1928-31)
07-22-2023, 12:50 PM
|
Replies: 9
Views: 1,211
|
Forum: Model A (1928-31)
07-22-2023, 12:47 PM
|
Replies: 9
Views: 1,211
Re: Rear spring perch fix procedure
Brent
Thanks so much for your good advice. Fortunately I do have another axle housing I can use.
I'll get the existing one off first to see how badly it is worn, and if salvageable, use that to...
|
Forum: Model A (1928-31)
07-22-2023, 10:22 AM
|
Replies: 9
Views: 1,211
Re: Rear spring perch fix procedure
Thanks. For reassembly I do have a rear spring spreader. Thanks, I just didn't want to proceed without checking first if I was overlooking something.
|
Forum: Model A (1928-31)
07-22-2023, 08:41 AM
|
Replies: 9
Views: 1,211
Rear spring perch fix procedure
Gents:
I just powder coated wheels for a 1930 coupe driver that I just picked up locally. So happy to dress up the black plain-Jane coupe! When removing the drivers side wheel, I was horrified...
|
Forum: Model A (1928-31)
06-30-2023, 01:30 PM
|
Replies: 13
Views: 1,431
Re: Timing Gear Replacement
Gents - I used the impact wrench. First try nothing. Second try nothing. Third try the nut spun off, so easily I thought I dreamt it!!!
Thanks for the great advice.
Don
|
Forum: Model A (1928-31)
06-28-2023, 03:37 PM
|
Replies: 13
Views: 1,431
Re: Timing Gear Replacement
Thanks very much for your advice. I do have an impact wrench and the special socket for the nut. I will try that first before any heat.
Thanks again.
|
Forum: Model A (1928-31)
06-28-2023, 03:07 PM
|
Replies: 13
Views: 1,431
Timing Gear Replacement
Model A Gurus - I need some advice:
Attempted to remove the timing gear on an engine rebuilt 40 years ago but on the shelf and never installed. Assembled the engine, but saw a small chip on one...
|
Forum: Model A (1928-31)
12-30-2021, 07:49 PM
|
Replies: 20
Views: 3,219
|
Forum: Model A (1928-31)
12-30-2021, 07:34 PM
|
Replies: 31
Views: 2,831
Re: Assembly - fan to water pump
Thanks to all for your comments and suggestions. I ground down the pump housing casting where it was a bit oblong. I placed the spacer with Allen set screw between the fan and the casting end to...
|
Forum: Model A (1928-31)
12-23-2021, 12:07 PM
|
Replies: 31
Views: 2,831
Re: Assembly - fan to water pump
Thanks Keith, will check the measurements again and if I need to bring it back some, maybe I can use a teflon flat washer that is included with the spacer (which I don't need!). The partition in the...
|
Forum: Model A (1928-31)
12-20-2021, 03:58 PM
|
Replies: 31
Views: 2,831
|
Forum: Model A (1928-31)
12-20-2021, 12:50 PM
|
Replies: 31
Views: 2,831
|
Forum: Model A (1928-31)
12-20-2021, 12:23 AM
|
Replies: 31
Views: 2,831
Re: Assembly - fan to water pump
The impeller is pressed on - that would be a good solution to move the impeller a little bit to gain room on the other fan end. Thanks for all the great advice. I forgot about the importance of the...
|
Forum: Model-T
12-19-2021, 11:48 PM
|
Replies: 0
Views: 938
|
Forum: Model A (1928-31)
12-19-2021, 05:57 PM
|
Replies: 31
Views: 2,831
|
Forum: Model A (1928-31)
12-19-2021, 04:45 PM
|
Replies: 31
Views: 2,831
Re: Assembly - fan to water pump
The water pump is from my 1930 Ford roadster that my Dad bought in 1948 and stored until I got it running last year, and then I tore it apart to rebuild engine and restore it. The water pump was...
|
Forum: Model A (1928-31)
12-19-2021, 04:42 PM
|
Replies: 31
Views: 2,831
|
Forum: Model A (1928-31)
12-19-2021, 04:41 PM
|
Replies: 31
Views: 2,831
|
Forum: Model A (1928-31)
12-19-2021, 04:40 PM
|
Replies: 31
Views: 2,831
Re: Assembly - fan to water pump
Thanks for the info. I think the problem is the taper in the fan. The shaft and rebuild kit fit perfect. However, the fan slides all the way back to hit the housing and only in that position will...
|
Forum: Model A (1928-31)
12-19-2021, 03:06 PM
|
Replies: 31
Views: 2,831
Re: Assembly - fan to water pump
I am using my original casting, just using repro rebuild kit and fan from Snyder's. Hate to alter the original!
https://ibb.co/v4NWrkD
https://ibb.co/N1992dN
|
Forum: Model A (1928-31)
12-19-2021, 02:47 PM
|
Replies: 31
Views: 2,831
Assembly - fan to water pump
This morning I was on my merry way reassembling my water pump and 2 blade repro fan from Snyder's. When I mounted the fan on the shaft with keyway, the fan pulley dropped down over the water pump...
|