Forum: Model A (1928-31)
03-29-2024, 01:55 PM
|
Replies: 9
Views: 584
Ring gear replacement
When removing the old ring gear, after heating it up, do you tap it forward toward the engine or backward toward the transmission???
Thanks,guys. This is first time I have tried this.
|
Forum: Model-A
02-28-2024, 12:49 PM
|
Replies: 0
Views: 201
Front Axle
I need a straight front axle, don't necessarily need wishbone, spring perches, etc. Hoping I can find one in Minnesota so I can pick it up.
|
Forum: Model A (1928-31)
12-20-2023, 11:48 AM
|
Replies: 9
Views: 761
Re: Rear spring perches
Thanks, Guys! This website is amazing! I think I will try the graphite rod route an look for replacement housings as a backup.
Jim in
|
Forum: Model A (1928-31)
12-19-2023, 03:32 PM
|
Replies: 9
Views: 761
Rear spring perches
I need to repair my rear spring perches that have worn through.
Somewhere I remember seeing a procedure where you cut a section of steel tubing and weld it inside the old perch.
Does this ring...
|
Forum: Model A (1928-31)
10-16-2023, 05:06 PM
|
Replies: 25
Views: 1,723
Lightened flywheel
Does anyone know where I can buy a lightened flywheel for my '31 coupe?
|
Forum: Model A (1928-31)
08-03-2023, 11:38 AM
|
Replies: 9
Views: 992
Float-A-Motor Question
I am trying to install a Float-A-Motor. The spacers for the rear engine mount seem too long. The installation diagram shows them going through the rubber pad and the frame, but the nuts will not...
|
Forum: Model A (1928-31)
06-05-2023, 11:35 AM
|
Replies: 10
Views: 1,568
Valve spring keepers
I am putting modern valves into a 28 block. I am having a Dickens of a time getting those little keepers on the valve stems with my fat fingers.
There must be a secret method known only to an...
|
Forum: Model A (1928-31)
04-14-2023, 10:43 AM
|
Replies: 8
Views: 1,363
Re: Gas & oil questions
Thanks for ll the suggestions. I particularly liked the one about removing the distributor and pouring oil down the hole...I would not have thought of it. I saw a Utube video about the oil system...
|
Forum: Model A (1928-31)
04-10-2023, 11:28 AM
|
Replies: 8
Views: 1,363
Gas & oil questions
My '31 coupe has been in storage for the last 60 years.
Can anyone bring me up to speed on current thinking about gas and oil for the Model A?
I assume 87 octane unleaded, but additives/no...
|
Forum: Model A (1928-31)
03-24-2023, 09:28 AM
|
Replies: 3
Views: 794
Clutch Question
Is the throwout bearing press fit to the hub? Or do I just have some 80 year old grease that make the bearing feel like it is press fit?
Thanks for any help.
Jim
|
Forum: Model A (1928-31)
03-10-2023, 03:31 PM
|
Replies: 11
Views: 2,149
|
Forum: Model A (1928-31)
03-10-2023, 12:02 PM
|
Replies: 11
Views: 2,149
Engine Stand Question
When mounting a model A engine to an engine stand, which bolt holes should be used?
The crankshaft sticks out so far in the back that it is proving difficult to get solid mount to then engine...
|
Forum: Early V8 (1932-53)
03-10-2023, 11:53 AM
|
Replies: 4
Views: 880
Engine Srand
When .mounting a model a engine on an engine stand, which bolt holes on the
engine should be used?
Thx.
|
Forum: Model A (1928-31)
02-18-2022, 12:54 PM
|
Replies: 3
Views: 802
Brake Assembly Diagrams
I have just moved and my resources are packed. Where can I find front and rear brake assembly diagrams?
|
Forum: Model A (1928-31)
04-19-2018, 12:26 PM
|
Replies: 1
Views: 1,383
Re: Model A panel/subrail help is
I replaced the rear half subrails on my '31 coupe...turned out to be fairly easy. I had my body off the frame.
Cut the old subrails out just behind the doorposts as square as possible. I...
|
Forum: Model A (1928-31)
03-27-2018, 11:46 AM
|
Replies: 4
Views: 1,930
|
Forum: Model A (1928-31)
03-26-2018, 04:03 PM
|
Replies: 4
Views: 1,930
Rear spare mount question
My '31 Deluxe Coupe w/rumble seat was hit from behind 60 years ago when I was in high school. Now I'm restoring it but can't remember how the inner curved panel/outer curved panel/rear spare tire...
|
Forum: Model A (1928-31)
03-05-2018, 05:57 PM
|
Replies: 5
Views: 1,355
Riveting tricks?
Does anyone have any tricks for making nice looking rivets on floor pans, etc.? I think my air hammer is hitting too hard.
Thx
|
Forum: Model A (1928-31)
02-14-2017, 03:20 PM
|
Replies: 6
Views: 1,870
Re: Removing pedal shaft pin
I did it sorta like you described...ground the head off, drove the pin about halfway out and the lassoed it through the clutch inspection port, then drove it the rest of the way out and pulled the...
|
Forum: Model-A
01-18-2016, 03:56 PM
|
Replies: 0
Views: 548
|
Forum: Model A (1928-31)
09-07-2015, 11:47 AM
|
Replies: 10
Views: 2,031
EvapoRust question
I cannot get the end plugs in my drag link or tie rods to come loose. I have tried penetrating oil, WD-40, and acetone/ATF but they won't budge.
Will it help to squirt EvapoRust on them? Will...
|
Forum: Model A (1928-31)
06-08-2015, 09:39 AM
|
Replies: 1
Views: 1,012
Worn rear spring perches
My rear spring shackles have worn themselves completely through the bushings and well into to the spring perches on both sides.
Does anyone know how to repair the perches????
Thx.
|
Forum: Model A (1928-31)
05-11-2015, 12:45 PM
|
Replies: 16
Views: 4,128
Body/fender steel
Quick one...What gauge steel is used for the body and fenders on my '31 coupe?? Thx.
|
Forum: Model A (1928-31)
01-27-2015, 12:38 PM
|
Replies: 1
Views: 1,443
Woodgrain pictures???
Does anyone have any closeup pictures of the woodgraining in a '31 deluxe coupe? I have the colors, and I know which parts to woodgrain, but I'd love to see a picture of the window frames that shows...
|
Forum: Model A (1928-31)
01-12-2015, 10:33 PM
|
Replies: 4
Views: 1,711
|