Forum: Model A (1928-31)
06-29-2021, 10:24 AM
|
Replies: 9
Views: 4,912
|
Forum: Model A (1928-31)
06-28-2021, 09:42 AM
|
Replies: 9
Views: 4,912
Trico Windshield Wiper Motor Doesn't Oscillate
When I engage the switch the motor shaft moves one half cycle counter clockwise and stops. When I disengage the switch the shaft returns to its stop. The paddle has been rebuilt, there are all new...
|
Forum: Model A (1928-31)
10-04-2020, 02:43 PM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-18-2020, 11:30 AM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-15-2020, 01:04 PM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-14-2020, 08:53 AM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-14-2020, 08:49 AM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-14-2020, 08:36 AM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-12-2020, 08:28 AM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-11-2020, 05:17 PM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
09-11-2020, 09:50 AM
|
Replies: 25
Views: 3,686
|
Forum: Model A (1928-31)
12-23-2019, 11:57 AM
|
Replies: 6
Views: 2,078
Re: Transmission Assembly
Chris and Tom: Thanks for your replies to my transmission noise. Tom, I think you may
be correct. I didn't replace the needle bearings in the cluster gear when I was working on the transmission. I...
|
Forum: Model A (1928-31)
12-13-2019, 12:44 PM
|
Replies: 6
Views: 2,078
Transmission Assembly
Andrews says that when assembling the transmission if the spacer ring that goes on the end of the main shaft before the main shaft is put into the main drive gear, is left out, the needle pilot...
|
Forum: Model A (1928-31)
09-28-2019, 08:31 AM
|
Replies: 4
Views: 2,059
Insert Main Bearings
Since expert Babbitt pourers-scrapers are extremely rare and/or expensive, Snyder's offers insert main bearing sets as an alternative to the Babbitt bearings. They say that the block must be...
|
Forum: Model A (1928-31)
09-11-2019, 12:38 PM
|
Replies: 3
Views: 1,537
Re: Transmission Gears Locked
To all you who offered suggestions for unlocking the gears, the gears are free and the shift tower is installed. I can't tell you how appreciative I am. I probably used a little of everyone's...
|
Forum: Model A (1928-31)
09-09-2019, 12:52 PM
|
Replies: 3
Views: 1,537
Transmission Gears Locked
After I lifted the Shifting Tower on my 1930 Roadster to inspect possible damaged gears I have been unable to get the two neutral gears in position so I can reinstall the tower. I have hand-cranked...
|
Forum: Model A (1928-31)
12-09-2018, 02:39 PM
|
Replies: 5
Views: 1,856
Trico Wiper Motor Moves Only One Direction
I just finished rebuilding the original Trico motor on my 1930 standard roadster. When I pull out the sliding switch the wiper blade moves to the left and stops. When I push in the sliding switch...
|
Forum: Model A (1928-31)
08-01-2018, 06:12 PM
|
Replies: 52
Views: 15,225
|
Forum: Model A (1928-31)
07-14-2018, 04:29 PM
|
Replies: 52
Views: 15,225
|
Forum: Model-A
09-01-2017, 08:09 AM
|
Replies: 0
Views: 996
|
Forum: Model A (1928-31)
11-02-2016, 07:02 PM
|
Replies: 10
Views: 2,303
|
Forum: Model A (1928-31)
11-01-2016, 07:27 PM
|
Replies: 10
Views: 2,303
Separating the transmission from the drviveshaft
I have a 1931 roadster frame with only the transmission, differential and rear axles, and radius rods installed. I have removed all the bolts that hold the universal joint to the driveshaft and...
|
Forum: Model A (1928-31)
12-12-2015, 07:29 PM
|
Replies: 2
Views: 1,257
|
Forum: Model-A
10-29-2015, 02:41 PM
|
Replies: 0
Views: 931
|
Forum: Model A (1928-31)
01-09-2015, 11:15 AM
|
Replies: 8
Views: 2,710
|