Forum: Early V8 (1932-53)
01-05-2015, 01:53 AM
|
Replies: 11
Views: 2,089
Re: Heater motor for parts?
Dave , I managed to get the Napa 12 v to fit my heater box by extending the sheet metal case by the 1/4" , looks fine. Easy to do
|
Forum: Early V8 (1932-53)
12-11-2014, 04:27 PM
|
Replies: 7
Views: 1,876
Re: 1939 Ford deluxe headlight rings
Agree with the rest above, but if you want to use them you can make them work. There really is only 2 mounting points the top and the bottom. The side points seem to be for alignment only. On the top...
|
Forum: Early V8 (1932-53)
12-11-2014, 04:22 PM
|
Replies: 7
Views: 1,712
Re: Front seat stands? 39 Ford deluxe Tudoor?
Any way you can post a picture?
I think my conv't and the tudoor share the same seat. My seat has rails that go between the seat frame and the feet. The rails are perpendicular to the floor and...
|
Forum: Early V8 (1932-53)
08-09-2014, 08:26 PM
|
Replies: 6
Views: 1,858
|
Forum: Early V8 (1932-53)
06-30-2014, 07:13 PM
|
Replies: 7
Views: 2,021
Re: 39 pickup heaters
I don't have mine in front of me, but I would think it is the middle picture, right hand side version. The inlet/outlet tubes are nearest to the defroster hoses, keeping everything up high. Did you...
|
Forum: Early V8 (1932-53)
06-17-2014, 02:42 PM
|
Replies: 17
Views: 4,127
|
Forum: Early V8 (1932-53)
04-21-2014, 06:58 PM
|
Replies: 15
Views: 3,367
|
Forum: Early V8 (1932-53)
03-10-2014, 01:27 PM
|
Replies: 47
Views: 12,768
|
Forum: Early V8 (1932-53)
03-10-2014, 01:19 PM
|
Replies: 4
Views: 1,110
Re: 40 wagon antenna question
Do you have the interior "C" clip installed? Because the antenna aligns based on the chrome bumps in the antenna, and the plastic holder that goes through the car. The "C" clamps put pressure on...
|
Forum: Early V8 (1932-53)
03-10-2014, 01:14 PM
|
Replies: 12
Views: 2,189
Re: Door lock cylinder
my square shaft has a hole in the center, so I just use a wire to align the square shaft as I am inserting it
|
Forum: Early V8 (1932-53)
10-25-2013, 03:51 PM
|
Replies: 3
Views: 1,221
|
Forum: Early V8
01-28-2013, 04:02 PM
|
Replies: 0
Views: 1,875
1939 top loader transmission
Ford flathead transmission, Recently rebuilt. w/syncro's top shifter, used in a 1939 car with 8BA block
Prefer not to ship
|
Forum: Early V8
01-28-2013, 04:00 PM
|
Replies: 1
Views: 2,064
Columbia Rear End & controls
1939 Columbia Rear end with controls and speedometer adapter . I believe this fits years 1935, 1946, 1937, 1938, 1939, 1940. Rear end has been bulletproofed, Includes setup for 1940 brakes/drums. I...
|
Forum: Early V8 (1932-53)
08-02-2012, 02:59 PM
|
Replies: 85
Views: 24,513
Re: Barn find 1940 ford conv. Value
Repectfully, I think $20K is a little high but you may be able to find someone, I think $14K to $17K is the range based on the condition described. There are a lot of specialized parts on a conv't,...
|
Forum: Early V8 (1932-53)
07-21-2012, 04:03 PM
|
Replies: 4
Views: 1,796
|
Forum: Early V8 (1932-53)
07-21-2012, 04:01 PM
|
Replies: 6
Views: 2,040
Re: 39 conv top irons question
Not standard, but there is a company that makes them, Is is possible they came from there?
http://catalog.superiorcarpartsinc.com/viewitems/top-irons-2/convertible-coupe-top-irons?
|
Forum: Early V8 (1932-53)
06-18-2012, 02:34 PM
|
Replies: 6
Views: 1,581
|
Forum: Early V8 (1932-53)
06-18-2012, 02:22 PM
|
Replies: 2
Views: 1,306
Re: Horn Repair
My car had the dual horns. The screw is the only thing that held the dome on. I would lightly pry where the mousehole is for the wire exit. I agree, PB blaster should help. Maybe tap the area where...
|
Forum: Early V8 (1932-53)
06-18-2012, 02:15 PM
|
Replies: 9
Views: 1,607
|
Forum: Early V8 (1932-53)
10-06-2011, 03:14 PM
|
Replies: 13
Views: 5,185
|
Forum: Early V8 (1932-53)
09-13-2011, 02:11 PM
|
Replies: 6
Views: 1,581
Re: Swap meets N. CA in late Sept or mid Oct.
RG 32 swap meet
Event Dates: September 25, 2011 - September 25, 2011
Location: Campbell, California
Early Ford V8 Club Ford parts all years swap meet
1600 Dell Ave Campbell CA
Sunday...
|
Forum: Early V8
09-12-2011, 03:29 PM
|
Replies: 2
Views: 1,496
|
Forum: Early V8 (1932-53)
09-02-2011, 01:15 PM
|
Replies: 5
Views: 2,640
|
Forum: Early V8
09-02-2011, 01:13 PM
|
Replies: 1
Views: 1,281
Re: 6 volt heater motor
Motor looks like it is from a 1940 heater, especially the fwd/rev (with speed control by switch resistance) reference.
|
Forum: Early V8 (1932-53)
07-08-2011, 04:44 PM
|
Replies: 20
Views: 3,602
Re: TDC on a 59 engine
I like the tie wrap method. Just get the biggest tie wrap you can find, stuff the tail into the spark hole, manually turn the crank until the piston tops out, rotate it to the other direction until...
|