Forum: Model A (1928-31)
05-16-2024, 06:31 PM
|
Replies: 15
Views: 635
Re: cam lube
I use isky rev lube on all new rebuilds. T’s to SBC. Why take a chance
|
Forum: Model A (1928-31)
05-13-2024, 08:58 PM
|
Replies: 16
Views: 815
Re: valve parts application
I come up with gmc 305 v6 for that valve. Supersedes to s2326. Its not available thru SBI. Maybe try egge or ebay
|
Forum: Early V8 (1932-53)
04-24-2024, 04:18 PM
|
Replies: 6
Views: 589
Re: Lincoln pinion backlash
Think those parts came as an assembled pinion/ housing and ring gear so no specs were published. At least none ive been able to find. I would say tooth contact pattern is more important than lash...
|
Forum: Early V8 (1932-53)
04-09-2024, 03:39 PM
|
Replies: 6
Views: 381
|
Forum: Early V8 (1932-53)
04-09-2024, 07:55 AM
|
Replies: 6
Views: 381
Re: 49 f-1 engine color
Ok thanks. think this will suffice or would the tangerine/ orangeish color be more accurate?
|
Forum: Early V8 (1932-53)
04-09-2024, 07:15 AM
|
Replies: 6
Views: 381
49 f-1 engine color
What is the correct color? Ive been told blue, red/ orange or bronze. Anyone know for sure? Thanks
|
Forum: Early V8 (1932-53)
02-04-2024, 12:10 PM
|
Replies: 28
Views: 1,528
|
Forum: Early V8 (1932-53)
02-03-2024, 08:57 PM
|
Replies: 5
Views: 451
Re: 325 gears
Shim between pinion and bearing moves it closer to axle centerline and reduces backlash
|
Forum: Early V8 (1932-53)
02-03-2024, 06:58 PM
|
Replies: 5
Views: 451
Re: 325 gears
Thatll be on monday but im sure itll be non productive
|
Forum: Early V8 (1932-53)
02-03-2024, 05:24 PM
|
Replies: 5
Views: 451
325 gears
Looking for anyone who has installed this ratio in an early rear end. Done many 354’s but not this ratio. Im no noobie when it comes to rebuilding these but this has me about ready to throw in the...
|
Forum: Early V8 (1932-53)
07-21-2023, 08:08 PM
|
Replies: 9
Views: 862
|
Forum: Model A (1928-31)
07-17-2023, 02:13 PM
|
Replies: 2
Views: 561
Clutch finger adjustment
So have to ask what is the correct measurement from back of cover to the fingers? Im reading 11/16 or 3/4 depending on the source. Ive checked some old pressure plates with new disks and usually...
|
Forum: Model A (1928-31)
07-03-2023, 07:00 PM
|
Replies: 12
Views: 1,221
|
Forum: Model A (1928-31)
07-03-2023, 04:43 PM
|
Replies: 12
Views: 1,221
|
Forum: Model A (1928-31)
07-03-2023, 01:13 PM
|
Replies: 12
Views: 1,221
|
Forum: Model A (1928-31)
07-03-2023, 09:07 AM
|
Replies: 12
Views: 1,221
Cork rear main seal opinions?
I havent found much info regarding this type seal. I dont think they are available currently. Has anyone got any feedback as to how well they work. Or dont?
|
Forum: Early V8 (1932-53)
06-06-2023, 01:53 PM
|
Replies: 37
Views: 2,842
|
Forum: Early V8 (1932-53)
06-06-2023, 08:59 AM
|
Replies: 9
Views: 754
|
Forum: Early V8 (1932-53)
06-06-2023, 08:38 AM
|
Replies: 37
Views: 2,842
Re: 8ba fuel pump rod getting stuck
FYI. I just used one of the current pump rebuild kits. The eye in the diaphragm rod was binding on the back side of the arm hook that goes in it on full extension. I found it because it would rack...
|
Forum: Early V8 (1932-53)
06-06-2023, 08:16 AM
|
Replies: 9
Views: 754
Small bore 59a ?
Can a 3.062 bore 59a be safely taken out to 3.248 for a 265 build? Inclined to think yes provided the block castings are all the
Same
|
Forum: Model T (1909-1927)
10-29-2022, 09:45 AM
|
Replies: 2
Views: 1,423
Re: KR Wilson HCCT
There is a wiring diagram and lots of info on the mtfca website. There is also a book concerning those available from there
|
Forum: Model A (1928-31)
10-28-2022, 06:20 PM
|
Replies: 3
Views: 906
|
Forum: Model A (1928-31)
10-28-2022, 05:46 PM
|
Replies: 3
Views: 906
Model a pressure plates
Ive been trying to figure out an issue with rebuilt pressure plates and correct finger height. The disk is about .365 thick. Distance from flywheel disk face to plate mounting surface is 1.135. Not...
|
Forum: Model A (1928-31)
08-13-2022, 09:08 AM
|
Replies: 17
Views: 3,189
|
Forum: Model A (1928-31)
08-09-2022, 05:44 PM
|
Replies: 9
Views: 1,529
|