Forum: Model A (1928-31)
08-03-2023, 07:47 PM
|
Replies: 15
Views: 3,382
|
Forum: Model A (1928-31)
04-21-2023, 06:40 PM
|
Replies: 15
Views: 3,382
|
Forum: Model A (1928-31)
04-02-2023, 08:12 AM
|
Replies: 15
Views: 3,382
|
Forum: Model A (1928-31)
03-31-2023, 01:59 PM
|
Replies: 15
Views: 3,382
|
Forum: Model A (1928-31)
03-30-2023, 06:23 PM
|
Replies: 15
Views: 3,382
|
Forum: Model A (1928-31)
03-29-2023, 07:43 PM
|
Replies: 15
Views: 3,382
|
Forum: Model A (1928-31)
03-29-2023, 05:00 PM
|
Replies: 15
Views: 3,382
Source for interior pre-cut panels or Templates
I’m having a hard time finding pre-cut un-upholstered panels for my 29 Tudor. Is there anyone making them anymore? I previously used Cartouche in the past…
What about templates that can be...
|
Forum: Model-A
03-29-2023, 04:47 PM
|
Replies: 0
Views: 689
|
Forum: Model A (1928-31)
03-29-2023, 03:58 PM
|
Replies: 22
Views: 3,104
|
Forum: Model-A
06-04-2018, 11:28 AM
|
Replies: 0
Views: 774
SPARTON Horn 12volt
Used, in excellent condition. No dents or dings. $100 cheaper than new.
PayPal accepted. $15 shipping. Thank you
|
Forum: Model A (1928-31)
10-22-2011, 12:31 PM
|
Replies: 6
Views: 1,902
Re: Brake/Tail Lights (Is this normal?)
I have the two bulb lights with single filament. It appears they used the stock wire harness and added to it. I will take some detailed pictures and post later this weekend. Thanks for the help!!...
|
Forum: Model A (1928-31)
10-22-2011, 10:48 AM
|
Replies: 6
Views: 1,902
Brake/Tail Lights (Is this normal?)
I have a question regarding my taillights. Any input is greatly appreciated.
When I have my lights turned on in the evening, the tail lights are extremely bright. So bright, its hard to tell...
|
Forum: Model A (1928-31)
07-22-2011, 09:51 AM
|
Replies: 3
Views: 1,482
|
Forum: Model A (1928-31)
06-17-2011, 04:54 PM
|
Replies: 1
Views: 1,297
|
Forum: Model A (1928-31)
06-06-2011, 11:03 AM
|
Replies: 40
Views: 8,082
|
Forum: Model A (1928-31)
06-05-2011, 09:05 AM
|
Replies: 6
Views: 1,748
Re: transmission
There are plenty posts on that subject. Not to be rude...but try using the search feature. You will also find a load of info on The HAMB site...again, try using the search tool... it works.
...
|
Forum: Model A (1928-31)
06-02-2011, 04:42 PM
|
Replies: 1
Views: 1,316
|
Forum: Model A (1928-31)
05-28-2011, 04:08 PM
|
Replies: 10
Views: 2,180
Re: Diagnosis
Interesting. Could you (or anyone) please describe how float-a-motor mounts could be to tight? Are you referring that the rubber pads are to compressed (over tightened)? Thanks!!
|
Forum: Model A (1928-31)
05-28-2011, 01:11 PM
|
Replies: 10
Views: 2,180
Re: Diagnosis
Pull that pan... do the checks. I will guess, it's a couple rods and the mains are fine.
|
Forum: Model A (1928-31)
05-28-2011, 08:12 AM
|
Replies: 4
Views: 1,679
Re: Competed 1st Shim Job on the Rods and Mains
Thanks boys. My body is a little stiff this morning. Not oil leaks last night after my short test drive. Going to take her out this morning while its still cool and put some miles on her. Have a...
|
Forum: Model A (1928-31)
05-28-2011, 08:07 AM
|
Replies: 12
Views: 9,493
Re: Engine Knock Diagnosis???
I just completed my 1st shim job on the mains and rods. Do some research and give it a try. It really wasn't that bad. I had a great time (got dirty) and learned a few things. Very satisfying as...
|
Forum: Model A (1928-31)
05-27-2011, 07:27 PM
|
Replies: 4
Views: 1,679
Competed 1st Shim Job on the Rods and Mains
This was done while the engine was in the car. I think the next time it will come out... not sure if that would be more work or not? Great learning experience. The babbitt's are all fine. I used...
|
Forum: Model A (1928-31)
05-26-2011, 10:15 AM
|
Replies: 2
Views: 1,330
Re: On to next project!
I couldn't get mine to stick very well. I had to removed all the peel and stick material from the rubber and use contact cement to get then to adhear.... making sure the boards are extremely clean.
|
Forum: Model A (1928-31)
05-23-2011, 09:19 PM
|
Replies: 26
Views: 5,973
|
Forum: Model A (1928-31)
05-23-2011, 05:43 PM
|
Replies: 16
Views: 3,268
Re: Hand Cranking Rookie Question
Very good point.
I got the oil pan off, what a chore that was. No babbit material in the pan... thats good. There are plenty of shims in place on both the mains and rods... thats also good. I...
|