Forum: Model A (1928-31)
03-18-2024, 07:08 PM
|
Replies: 10
Views: 557
Re: Choke rod
make sure the rod itself is straight and true. Also confirm the arm linkage on the carburetor is not gummied up either.
|
Forum: Early V8 (1932-53)
03-17-2024, 07:34 PM
|
Replies: 19
Views: 718
Re: My 33 BB Truck
I love that green, wish I could just snap my fingers and mine could be GREEN. Lovely work on the wood bed too.
|
Forum: Model A (1928-31)
02-29-2024, 09:38 PM
|
Replies: 25
Views: 1,581
Re: Pre Osha
First pic on this thread is a Chevy garage, ............ Ford never did that !!!!!!
|
Forum: Early V8 (1932-53)
02-22-2024, 01:01 AM
|
Replies: 15
Views: 1,065
|
Forum: Model A (1928-31)
02-14-2024, 02:35 PM
|
Replies: 22
Views: 7,581
Re: Arabian Sand Color
the new Toyota trucks have a color called "muddy" I believe, looks very close to Arabian Sand
|
Forum: Model A (1928-31)
02-14-2024, 02:30 PM
|
Replies: 28
Views: 1,498
|
Forum: Model A (1928-31)
01-30-2024, 01:05 AM
|
Replies: 8
Views: 661
|
Forum: Model A (1928-31)
11-29-2023, 11:03 AM
|
Replies: 2
Views: 516
removing hubs to replace bearings
thanks for all advice and support!
first time removing rear hubs to inspect possible worn out wheel bearings, do I need to back off the brake adjustment to free up all the pads inside ?
the online...
|
Forum: Early V8 (1932-53)
11-21-2023, 12:57 AM
|
Replies: 25
Views: 1,410
|
Forum: Model A (1928-31)
11-18-2023, 10:06 AM
|
Replies: 7
Views: 650
|
Forum: Early V8 (1932-53)
11-18-2023, 10:04 AM
|
Replies: 30
Views: 4,896
Re: 1936 Ford Telephone Truck
Beautiful, inside and out. It is cool that you have (he kept) all the service parts and tools for the inside compartments. The whole package is priceless.
|
Forum: Early V8 (1932-53)
11-16-2023, 09:45 PM
|
Replies: 8
Views: 487
Re: 1933 pick up firewall removal
Firewall is all part of the cab, cowl, top and rear panel.
mine was a swiss cheese too but I just found grommet hole plugs of various sizes to snap in place and covered with speed shop decals,...
|
Forum: Early V8 (1932-53)
11-10-2023, 10:18 PM
|
Replies: 4
Views: 432
|
Forum: Model A (1928-31)
11-10-2023, 10:15 PM
|
Replies: 8
Views: 631
|
Forum: Model A (1928-31)
11-07-2023, 08:04 PM
|
Replies: 15
Views: 1,387
|
Forum: Model A (1928-31)
10-24-2023, 09:25 PM
|
Replies: 47
Views: 4,066
Re: black wall tires
I have had Firestones for 22 years. They fit just fine into the side mount wheel well. I'm going with Goodyears in 2024. Gonna try the diamond treads.
|
Forum: Early V8 (1932-53)
10-23-2023, 09:44 PM
|
Replies: 81
Views: 4,276
|
Forum: Early V8 (1932-53)
10-23-2023, 09:42 PM
|
Replies: 5
Views: 585
|
Forum: Early V8 (1932-53)
10-20-2023, 11:50 PM
|
Replies: 18
Views: 966
|
Forum: Model A (1928-31)
09-14-2023, 10:09 PM
|
Replies: 62
Views: 6,027
|
Forum: Model A (1928-31)
08-20-2023, 10:55 PM
|
Replies: 16
Views: 1,436
|
Forum: Model A (1928-31)
08-19-2023, 11:34 PM
|
Replies: 18
Views: 1,786
Re: Wesenberg EVR- voltage cycling problem
I have had one of Tom's EVR units on my car for about 10-12 years and the AMP gauge needle is as steady as ever at about 3 amps. I had him restore three powerhouse generators, one is a 3 brush and...
|
Forum: Model A (1928-31)
08-19-2023, 12:42 AM
|
Replies: 13
Views: 1,245
Re: Throttle Repair
Use the one that will operate with the least amount of mending. I dismembered two pitted ones to utilize good springs and rods that had no signs of wear. Takes a lot of patience to fit and adjust if...
|
Forum: Model A (1928-31)
08-16-2023, 10:02 PM
|
Replies: 11
Views: 1,265
Re: Battery hold down clamps
with the factory battery support bolts at opposite corners, using the full-frame hold down method I placed shrink tubing around the ends of the two battery cable clamps and have never had any issues...
|
Forum: Early V8 (1932-53)
08-16-2023, 09:57 PM
|
Replies: 55
Views: 2,656
Re: Gas Pedal Travel
Of the linkage from firewall to carb with the turn-buckle, trim the longer rod maybe 1/8" to 1/4" shorter to give the pedal more room to achieve full WOT.... since yours is cut already..... that may...
|