Forum: Early V8 (1932-53)
Yesterday, 05:44 PM
|
|
Replies: 12
Views: 391
Re: Ford holley carb fuel inlet fitting
These are repair fittings, upon a time easy to get NAPA etc.....not on the active here
in Buffalo N.Y. anymore. I'll buy a swap meet 94 if has that fitting on it. The fitting from Mikes is for a...
|
|
Forum: Early V8 (1932-53)
Yesterday, 10:02 AM
|
|
Replies: 19
Views: 559
|
|
Forum: Early V8 (1932-53)
01-23-2021, 08:27 PM
|
|
Replies: 19
Views: 559
Re: Holley 94 Rebuild - Something Strange
Did you get the blockage out ? If not put a 1/16 dia drill in your drill press and
center it over the bore. Carefully start the drill on the blockage. The blockage is
of course the 4 sided brass...
|
|
Forum: Early V8 (1932-53)
01-20-2021, 05:59 PM
|
|
Replies: 12
Views: 500
|
|
Forum: Early V8 (1932-53)
01-19-2021, 09:24 PM
|
|
Replies: 30
Views: 930
|
|
Forum: Early V8 (1932-53)
01-19-2021, 07:24 AM
|
|
Replies: 30
Views: 930
|
|
Forum: Early V8 (1932-53)
01-18-2021, 09:15 PM
|
|
Replies: 30
Views: 930
|
|
Forum: Early V8 (1932-53)
01-18-2021, 10:30 AM
|
|
Replies: 30
Views: 930
|
|
Forum: Early V8 (1932-53)
01-16-2021, 10:06 AM
|
|
Replies: 11
Views: 940
Re: Early Ford V8 Flea Market
Canfield Spring. Summer and Fall in OHIO is a go. Check out Dave and Ed's. I'm hoping
health concerns will be under control in time for the Fall event.
...
|
|
Forum: Early V8 (1932-53)
01-15-2021, 09:53 AM
|
|
Replies: 0
Views: 222
Dave & Ed's...schedule
Dave and Ed's swap meets schedule is out.....my fav CANFIELD is still
part of their production, spring , summer , fall.....I'm hoping things will be
more normal maybe by summer or fall. Very...
|
|
Forum: Early V8 (1932-53)
01-13-2021, 07:41 AM
|
|
Replies: 65
Views: 1,000
Re: Helmet Distributor Rebuild
Steve,
Regarding post #15 did you check point alignment ? This is the time to make sure the contacts close square. With the breaker plate fully assembled aligning the fixed arm to the...
|
|
Forum: Early V8 (1932-53)
01-12-2021, 03:56 PM
|
|
Replies: 17
Views: 555
|
|
Forum: Early V8 (1932-53)
01-12-2021, 12:38 PM
|
|
Replies: 17
Views: 555
|
|
Forum: Early V8 (1932-53)
01-09-2021, 09:57 PM
|
|
Replies: 9
Views: 502
Re: Initial start on new engine
Hold off with anti freeze until you're sure the engine is sound. Many anti freeze products will dissolve engine bearings if it finds it's way into your oil.
...
|
|
Forum: Early V8 (1932-53)
01-07-2021, 09:48 PM
|
|
Replies: 14
Views: 573
|
|
Forum: Early V8 (1932-53)
01-07-2021, 09:46 PM
|
|
Replies: 14
Views: 573
Re: Chevy distibutor question for Bubba...
Hey Pete,
Mallory and others made dual point conversions back in the day for DELCO
window distributors....quite often on e bay. Someone on the Barn mentioned he has some .
...
|
|
Forum: Early V8 (1932-53)
01-07-2021, 10:05 AM
|
|
Replies: 14
Views: 355
|
|
Forum: Early V8 (1932-53)
01-05-2021, 08:06 AM
|
|
Replies: 17
Views: 510
Re: 53’ 239 Flathead Water Pump Mounts
Tater,
V 8 Bob is seeing what I'm seeing....use the truck pumps with the ears and
wide belt pulleys. Hopefully your motor does have a wide crank pulley on it...if not they
are easy...
|
|
Forum: Early V8 (1932-53)
01-04-2021, 11:30 PM
|
|
Replies: 24
Views: 915
|
|
Forum: Early V8 (1932-53)
01-03-2021, 04:38 PM
|
|
Replies: 28
Views: 1,250
|
|
Forum: Early V8 (1932-53)
01-02-2021, 11:11 AM
|
|
Replies: 24
Views: 1,042
Re: Throttle return spring and baling wire
Marv,
There's a return spring on the fire wall mounted linkage...some where...that is tired so grampa got 'er done his way. Better check those screws on the carb air horn,
they are...
|
|
Forum: Early V8 (1932-53)
01-02-2021, 10:19 AM
|
|
Replies: 16
Views: 559
Re: New pinion bearings
VanPelt is an excellent source....do not forget the axle seals and premium gasket sets,
VP has them as well.
...
|
|
Forum: Early V8 (1932-53)
12-31-2020, 07:59 AM
|
|
Replies: 13
Views: 678
|
|
Forum: Early V8 (1932-53)
12-30-2020, 10:35 AM
|
|
Replies: 29
Views: 1,210
|
|
Forum: Early V8 (1932-53)
12-30-2020, 08:30 AM
|
|
Replies: 67
Views: 1,838
|
