Forum: Early V8 (1932-53)
Yesterday, 01:44 PM
|
|
Replies: 5
Views: 254
|
|
Forum: Early V8 (1932-53)
01-09-2021, 01:38 PM
|
|
Replies: 8
Views: 391
|
|
Forum: Early V8 (1932-53)
01-09-2021, 11:40 AM
|
|
Replies: 8
Views: 391
|
|
Forum: Early V8 (1932-53)
01-07-2021, 05:29 PM
|
|
Replies: 8
Views: 391
|
|
Forum: Early V8 (1932-53)
12-24-2020, 11:01 AM
|
|
Replies: 13
Views: 809
|
|
Forum: Questions & Suggestions
12-21-2020, 09:22 PM
|
|
Replies: 2
Views: 210
Re: Trunk light
If it is a 52'-53' Merc, the trunk light is controlled, by the headlight switch.
|
|
Forum: Early V8 (1932-53)
12-21-2020, 09:31 AM
|
|
Replies: 47
Views: 2,364
Re: where is this all going
Something to pass the time from Down Under, where it is is Summer:
https://www.youtube.com/watch?v=TN3sO7sYmdc
https://www.youtube.com/watch?v=M8gzeGPVuXU
|
|
Forum: Late V8 (1954+)
12-13-2020, 09:47 AM
|
|
Replies: 27
Views: 831
Re: Power steering cylinder
They do it by size, so get out your micrometer. I took the seals to them, and they measured them, and then came up with the proper seals. The biggest difference, is that they are the "loaded" seals,...
|
|
Forum: Late V8 (1954+)
12-12-2020, 06:32 PM
|
|
Replies: 27
Views: 831
|
|
Forum: Late V8 (1954+)
12-11-2020, 08:28 PM
|
|
Replies: 27
Views: 831
|
|
Forum: Late V8 (1954+)
12-11-2020, 04:52 PM
|
|
Replies: 27
Views: 831
|
|
Forum: Late V8 (1954+)
12-11-2020, 10:16 AM
|
|
Replies: 27
Views: 831
|
|
Forum: Early V8 (1932-53)
12-10-2020, 08:37 PM
|
|
Replies: 8
Views: 717
Re: Gas pump question
Gas Pump Heaven might be a good source. I have used them for parts numerous times.
https://gaspumpheaven.com/
|
|
Forum: Early V8 (1932-53)
12-06-2020, 12:20 PM
|
|
Replies: 21
Views: 1,126
Re: Engine Steady Rods
I always put a 2X4 under the front, behind the pulley. Maybe not the best, but I do acknowledge the risk of not supporting the front of the engine on a stand. Good reminder though.
|
|
Forum: Early V8 (1932-53)
12-05-2020, 02:14 PM
|
|
Replies: 21
Views: 1,126
Re: Engine Steady Rods
That was an engine I picked up, real cheap, to tear apart and then reassemble, basically to learn on, before I bought my 53' Merc.
|
|
Forum: Early V8 (1932-53)
12-05-2020, 01:08 PM
|
|
Replies: 21
Views: 1,126
|
|
Forum: Early V8
12-04-2020, 06:18 PM
|
|
Replies: 1
Views: 120
|
|
Forum: Early V8
11-29-2020, 01:55 PM
|
|
Replies: 1
Views: 120
Rear window trim for a 1953 Mercury convertable
I am looking for the two pieces of Stainless Steel trim, that go below the rear window, on a 1953 Mercury Convertible. Mine have been sanded and polished too many times.
royd13483@aol.com
(303)...
|
|
Forum: Early V8 (1932-53)
11-29-2020, 01:23 PM
|
|
Replies: 40
Views: 2,676
Re: Condenser
Since we are talking condensers here, anyone know who the manufacture of this one is. I am not familiar with the markings\symbol on the bottom. I have two of them, serving as back up.
|
|
Forum: Early V8 (1932-53)
11-28-2020, 10:08 AM
|
|
Replies: 7
Views: 725
Re: Muggy Weld
This is a brace, for a bow, part of my convertible top. It is made out of pot metal. The weld has held beautifully, and since it is part to the convertible top it get used quite often. The pictures...
|
|
Forum: Early V8 (1932-53)
11-25-2020, 01:55 PM
|
|
Replies: 28
Views: 5,335
|
|
Forum: Early V8 (1932-53)
11-23-2020, 08:54 PM
|
|
Replies: 40
Views: 2,676
Re: Condenser
G.M.,
Thanks for the information, as I never considered that. I am installing a new Echlin (ECH FA76) in my 53' Merc, to see if it makeds a diffrfence.
|
|
Forum: Early V8 (1932-53)
11-15-2020, 08:10 PM
|
|
Replies: 8
Views: 345
Re: Source for origional 53' Mercury trim clips
The only issue, is that the screws would go directly into the top material behind the body. The reason I am replacing the old ones, is that they were incorrect and I am having a new Stayfast top put...
|
|
Forum: Early V8 (1932-53)
11-15-2020, 05:59 PM
|
|
Replies: 8
Views: 345
|
|
Forum: Early V8 (1932-53)
11-15-2020, 04:11 PM
|
|
Replies: 8
Views: 345
|
