Forum: Early V8 (1932-53)
03-29-2024, 06:36 AM
|
Replies: 11
Views: 778
|
Forum: Early V8 (1932-53)
03-26-2024, 04:38 PM
|
Replies: 11
Views: 778
|
Forum: Early V8 (1932-53)
03-25-2024, 04:54 PM
|
Replies: 6
Views: 539
|
Forum: Early V8 (1932-53)
03-25-2024, 12:55 PM
|
Replies: 1
Views: 306
|
Forum: Early V8 (1932-53)
03-25-2024, 11:45 AM
|
Replies: 1
Views: 245
|
Forum: Early V8 (1932-53)
03-10-2024, 07:16 PM
|
Replies: 6
Views: 523
|
Forum: Early V8 (1932-53)
02-07-2024, 01:24 PM
|
Replies: 12
Views: 1,038
|
Forum: Early V8 (1932-53)
02-07-2024, 07:09 AM
|
Replies: 12
Views: 1,038
Lug nuts from Third Gen Auto
Has anyone bought lug nuts from them for 48 ford car. I can't seem to get hold of them. Do the threads start in a ways on the nuts or start at edge ? Thanks
Steve
|
Forum: Early V8 (1932-53)
10-18-2023, 09:39 AM
|
Replies: 10
Views: 671
|
Forum: Early V8 (1932-53)
10-17-2023, 05:15 PM
|
Replies: 10
Views: 671
|
Forum: Early V8 (1932-53)
10-17-2023, 08:08 AM
|
Replies: 10
Views: 671
|
Forum: Early V8 (1932-53)
10-16-2023, 05:50 PM
|
Replies: 10
Views: 671
|
Forum: Early V8 (1932-53)
10-12-2023, 03:03 PM
|
Replies: 7
Views: 530
|
Forum: Early V8 (1932-53)
10-11-2023, 06:11 PM
|
Replies: 7
Views: 530
48 grease seal
This summer I have had to replace right rear grease seal 3 times on my 48 ford conv. What could be worn that would do this ? Fluid is down about 3/4" below fill plug. Also bearing seems to float...
|
Forum: Early V8 (1932-53)
05-25-2016, 07:44 PM
|
Replies: 0
Views: 403
48 Ford horn parts diagram
I took the horn apart on my 48 ford and tipped the bowl of parts over and can't figure how it goes back together. Looking for detailed parts diagram. Thanks
|
Forum: Early V8 (1932-53)
03-16-2016, 12:39 PM
|
Replies: 2
Views: 916
|
Forum: Early V8 (1932-53)
03-09-2016, 09:03 AM
|
Replies: 7
Views: 1,774
Re: Voltage Reducer for 48 heater
TO RALPH M,
thanks for info. We were in North Pole, Alaska a couple of years ago. I believe that is where we went into a room that was -40 degrees with just tee shirts on. Kind of cold compared to...
|
Forum: Early V8 (1932-53)
03-07-2016, 04:24 PM
|
Replies: 7
Views: 1,774
Voltage Reducer for 48 heater
I'm converting my 48 Ford to 12 volt. I found a reducer BWD VR1. It says it will handle up to 4 AMP. Is that large enough to run heater motor on high. Thanks
|
Forum: Early V8 (1932-53)
02-09-2016, 06:31 PM
|
Replies: 3
Views: 1,203
12 volt coil and battery for 48 Ford
I'm converting my 48 Ford to 12 volt. What size battery would be best to fix in stock battery tray. Also what is a good coil to use with stock Ford Dis.
Who makes good drop resistors for gauges,...
|
Forum: Early V8 (1932-53)
02-04-2016, 05:41 PM
|
Replies: 2
Views: 958
|
Forum: Early V8 (1932-53)
01-29-2016, 09:17 AM
|
Replies: 19
Views: 3,279
Re: Uphostery kits
I got an kit from LB for my 48 Conv. and was very good but should have got all leather. the cloth material is starting to look quite worn for being 5 years old. e-mail me and I tell you about the top...
|
Forum: Early V8 (1932-53)
01-27-2016, 06:41 PM
|
Replies: 7
Views: 1,967
12 volt alt on 48 Ford
I'm thinking of converting my 48 Ford to 12 volt. Can you buy a bracket that will take a GM 1 wire alternator without machine work. Why I want to go this route is if I should have to replace on the...
|
Forum: Early V8 (1932-53)
01-25-2016, 09:14 AM
|
Replies: 8
Views: 2,493
|
Forum: Early V8 (1932-53)
09-11-2015, 12:36 PM
|
Replies: 14
Views: 2,206
|
Forum: Early V8 (1932-53)
09-03-2015, 10:39 PM
|
Replies: 9
Views: 2,540
48 Ford Conv. Right side mirror
I am looking for a mirror for right side of my 48 Ford Conv. Does anyone made a new one with the base as wide as side chrome ? Also any that will bolt to door that you can see from drivers side ?...
|