Forum: Model A (1928-31)
04-06-2020, 12:35 PM
|
|
Replies: 8
Views: 899
Re: Rear main oil pan seal
Appreciate all the replies. Both seals were the same length and I used the one that is slightly thinner and slightly narrower. I trimmed the length to exactly 6 11/16" and it fits really nice, got...
|
|
Forum: Model A (1928-31)
04-04-2020, 01:06 PM
|
|
Replies: 8
Views: 899
Rear main oil pan seal
Have a new oil pan gasket set and it comes with two different seals for the rear main cap. One has to be squeezed in to work the other will fit but not as tight. Which should be used. I noticed the...
|
|
Forum: Model A (1928-31)
07-30-2019, 04:55 PM
|
|
Replies: 10
Views: 1,194
|
|
Forum: Model A (1928-31)
07-30-2019, 02:59 PM
|
|
Replies: 10
Views: 1,194
|
|
Forum: Model A (1928-31)
05-13-2019, 02:45 PM
|
|
Replies: 5
Views: 782
Oval speedometer binds in reverse
My oval speedometer will sometimes bind up when going in reverse. Snapped my drive cable. It seems to work just fine going forward and seems to indicate speed good but when I go in reverse it will...
|
|
Forum: Model A (1928-31)
06-14-2018, 08:10 AM
|
|
Replies: 15
Views: 2,044
Re: Steering question
Hey Lynn, yeah I was asking on the HAMB also and I thought I pretty much had it by moving the pivot point about 3/4 inch forward but got a little better but still playing with it. Probably am over...
|
|
Forum: Model A (1928-31)
06-13-2018, 07:37 PM
|
|
Replies: 15
Views: 2,044
Re: Steering question
But the steering arm is connected to one spindle. Turning left its an inside wheel and turning right its an outside wheel. The tie rod connects them together but the inside wheel is turned to a...
|
|
Forum: Model A (1928-31)
06-13-2018, 11:46 AM
|
|
Replies: 15
Views: 2,044
Re: Steering question
As this is not a stock setup I have noticed with the steering arm that is mounted to the spindle has the ball end (drag link connection) directly over the centerline of the axle. In this...
|
|
Forum: Model A (1928-31)
06-13-2018, 05:57 AM
|
|
Replies: 15
Views: 2,044
Re: Steering question
Appreciate the input from everyone. The drag link is the stock model A so I think I should probably go through the steering box adjustments and make sure I didn't goof that up. Thanks
|
|
Forum: Model A (1928-31)
06-12-2018, 06:48 PM
|
|
Replies: 15
Views: 2,044
Steering question
I would really appreciate some assistance with a steering question. I am building a 28 roadster that is not totally stock but my frame is stock and I am using a two tooth steering box. I have a 33...
|
|
Forum: Model A (1928-31)
02-20-2018, 10:00 AM
|
|
Replies: 6
Views: 570
|
|
Forum: Model A (1928-31)
02-20-2018, 06:19 AM
|
|
Replies: 6
Views: 570
|
|
Forum: Model A (1928-31)
02-19-2018, 09:18 PM
|
|
Replies: 6
Views: 570
|
|
Forum: Model A (1928-31)
02-19-2018, 07:25 PM
|
|
Replies: 6
Views: 570
28 roadster radiator support rod mounts
I would love a little assistance if someone has some time. I have a 28 roadster that has one of those gas tank eliminator cowl panels and a upper firewall with a bead rolled panel. What I am...
|
|
Forum: Model-A
02-18-2013, 05:47 PM
|
|
Replies: 0
Views: 624
Dual Downdraft Intake Manifold
Looking for a nice dual downdraft intake manifold for stromberg carbs. Interested in either original or aftermarket in good shape. Not really interested in broken or repaired units. Appreciate any...
|
|
Forum: Model-A
11-22-2012, 11:11 AM
|
|
Replies: 2
Views: 1,052
High Compression head
Trying to find a high compression head. Been trying to get a 6.0 snyder head for almost a year now. At this point I'm not sure those are ever going to happen. Looking for repop or original type...
|
|
Forum: Model A (1928-31)
07-18-2012, 06:04 PM
|
|
Replies: 19
Views: 3,141
Re: Removing Rear Main Cap
I'm thinking you would be hitting the flywheel housing. Where it bolts to the block. Maybe turning the bolts so the flat on the head would line up and perhaps clear the housing.
|
|
Forum: Model A (1928-31)
06-10-2012, 06:05 AM
|
|
Replies: 4
Views: 1,332
Re: Oshkosh
Thank you Frank. Appreciate all the information.
Jim
|
|
Forum: Model A (1928-31)
06-09-2012, 09:19 PM
|
|
Replies: 4
Views: 1,332
|
|
Forum: Model A (1928-31)
06-09-2012, 08:54 PM
|
|
Replies: 4
Views: 1,332
Oshkosh
Could someone help me with a little information about the Oshkosh gathering. I live and work just a few minutes north of Oshkosh and was planning to take a couple days off work to go out and enjoy...
|
|
Forum: Model A (1928-31)
06-09-2012, 08:38 PM
|
|
Replies: 27
Views: 5,030
|
|
Forum: Model A (1928-31)
06-08-2012, 08:25 PM
|
|
Replies: 15
Views: 29,326
Re: 600W Gear Oil Discussion
Has anyone ever used Redline Shookproof Heavy gearlube. I used it in my Harley gearbox and it made a huge dfference in the smoothness of it's operation. Just curious.
Jim
|
|
Forum: Model A (1928-31)
08-04-2011, 08:45 PM
|
|
Replies: 3
Views: 1,025
|
|
Forum: Model A (1928-31)
05-05-2011, 11:50 AM
|
|
Replies: 31
Views: 7,002
Re: WOW, a Model A "trike"??
I got to agree with Stan. That guy probably loved every minute of building that and should get a lot of credit for seeing the project through. Absolutely not my cup of tea but certainly creative.
|
|
Forum: Model A (1928-31)
04-26-2011, 07:33 PM
|
|
Replies: 18
Views: 3,669
Re: Swap Meet Pages
Lots of varied replies. It is good to hear others input on this and I appreciate all of you taking the time to reply.
|
