Forum: Late V8
11-13-2020, 02:16 PM
|
|
Replies: 0
Views: 157
292 Ford forged steel truck crank
For sale one C1TE forged steel crankshaft for 292 Ford Y Block.
Measures up standard on rods and mains. Journals are very good with no scratching, etc. Polishing may clean it right up, at worst...
|
|
Forum: Late V8 (1954+)
07-13-2020, 08:14 AM
|
|
Replies: 7
Views: 706
|
|
Forum: Late V8
06-30-2020, 09:04 AM
|
|
Replies: 3
Views: 936
|
|
Forum: Late V8
06-30-2020, 09:03 AM
|
|
Replies: 2
Views: 789
|
|
Forum: Late V8
06-30-2020, 09:03 AM
|
|
Replies: 2
Views: 667
|
|
Forum: Late V8
06-30-2020, 09:02 AM
|
|
Replies: 3
Views: 776
|
|
Forum: Late V8
06-30-2020, 09:02 AM
|
|
Replies: 7
Views: 1,587
|
|
Forum: Late V8
06-30-2020, 09:01 AM
|
|
Replies: 5
Views: 1,585
|
|
Forum: Late V8
06-30-2020, 09:01 AM
|
|
Replies: 2
Views: 616
|
|
Forum: Late V8 (1954+)
05-18-2020, 03:18 PM
|
|
Replies: 20
Views: 1,536
Re: y block oil pressure
"will ADD 5-15 psi..."?? Could this be a misprint? Piping oil from the main galley to the rocker shafts will actually cause a drop in pressure. "
No misprint. I always pressurize rocker...
|
|
Forum: Late V8 (1954+)
05-18-2020, 07:32 AM
|
|
Replies: 20
Views: 1,536
Re: y block oil pressure
pressurizing your rocker arm assemblies will add 5-15 psi depending on what condition your oiling system/bearings are in.
|
|
Forum: Late V8 (1954+)
02-25-2020, 11:09 AM
|
|
Replies: 22
Views: 2,301
Re: Y block Mercury engine color?
Kultulz, not a problem. Actually, was quite proud to see one of my jobs used as a reference. Not sure, but believe '56 Merc was the same goldish/greenish white as the '55 block/heads.
|
|
Forum: Late V8 (1954+)
02-24-2020, 09:33 PM
|
|
Replies: 22
Views: 2,301
Re: Y block Mercury engine color?
The gold, red, white, batwing(caddy) air cleaner 292 is a motor I built for raceron's '56 Vicky. The gold colored block was a close match to the original color of the '55 Merc block used. The other...
|
|
Forum: Late V8
01-22-2020, 08:31 AM
|
|
Replies: 2
Views: 616
|
|
Forum: Late V8
01-22-2020, 08:31 AM
|
|
Replies: 5
Views: 1,585
|
|
Forum: Late V8
01-22-2020, 08:30 AM
|
|
Replies: 7
Views: 1,587
|
|
Forum: Late V8
01-22-2020, 08:29 AM
|
|
Replies: 3
Views: 776
|
|
Forum: Late V8
01-22-2020, 08:29 AM
|
|
Replies: 2
Views: 667
|
|
Forum: Late V8
01-22-2020, 08:28 AM
|
|
Replies: 2
Views: 789
|
|
Forum: Late V8
11-20-2019, 08:50 PM
|
|
Replies: 2
Views: 789
Ford 292-312 tri power setup
Ford Y-Block tri power set up. Edelbrock 573 intake and 3 Ford 94 carbs. The 573 intake is the large port intake, best used with ECZ-C and ECZ-G heads.
The carbs are ECG center carb and EBU end...
|
|
Forum: Late V8
11-09-2019, 04:11 PM
|
|
Replies: 2
Views: 616
1963 Fairlane 289 HiPo exhaust manifolds
One set of factory exhaust manifolds for 289 HiPo Fairlane application. These are very early take-offs for header installation, have been on the shelf for over 50 years and the condition of them is...
|
|
Forum: Late V8 (1954+)
11-09-2019, 04:00 PM
|
|
Replies: 14
Views: 912
|
|
Forum: Late V8 (1954+)
08-18-2019, 08:20 AM
|
|
Replies: 17
Views: 2,262
Re: Holley 1273-2S carburetor
My info has the Ford 4100 w/ 1.08 venturis at 480 cfm. The 1.12 4100 used typically on 390 engines is rated 600 cfm
|
|
Forum: Late V8
08-16-2019, 07:16 PM
|
|
Replies: 8
Views: 1,366
|
|
Forum: Late V8
08-15-2019, 08:51 PM
|
|
Replies: 5
Views: 1,585
|
