Forum: Early V8 (1932-53)
04-17-2022, 10:33 AM
|
Replies: 6
Views: 775
Re: '41 Front Park Lens - Removal
I did end up taking the assembly off and removing the screw underneath. The lens slid forward with some effort. The gaskets are all brittle, but it all seams to be very well made. I'm sure its the...
|
Forum: Early V8 (1932-53)
04-16-2022, 04:25 PM
|
Replies: 6
Views: 775
'41 Front Park Lens - Removal
Is there a trick to getting the lens out without breaking it. I can't seem to wiggle the lens loose. I don't remember how its held in place These are original lenses so any suggestions would be...
|
Forum: Early V8 (1932-53)
01-16-2020, 06:00 PM
|
Replies: 6
Views: 942
Re: Ignition Switch Lamp
Thanks Bryan Markell for the info. I am attaching two pictures. The first one is looking up and shows a small hole in the dash above the ignition switch. The second one is behind the dash and...
|
Forum: Early V8 (1932-53)
01-16-2020, 03:09 PM
|
Replies: 6
Views: 942
|
Forum: Early V8 (1932-53)
01-16-2020, 01:54 PM
|
Replies: 6
Views: 942
|
Forum: Early V8 (1932-53)
01-16-2020, 01:32 PM
|
Replies: 6
Views: 942
Ignition Switch Lamp
The wiring diagram for my '41 SuperD shows an "ignition switch lamp" and I have a bulb socket with the correct wire color dangling under my dash. Is there such a thing? I have searched and can't...
|
Forum: Early V8 (1932-53)
09-18-2017, 11:15 PM
|
Replies: 27
Views: 9,708
|
Forum: Early V8 (1932-53)
09-18-2017, 11:12 PM
|
Replies: 27
Views: 9,708
|
Forum: Early V8 (1932-53)
09-18-2017, 04:02 PM
|
Replies: 27
Views: 9,708
Re: Oil Pressure Sending Unit BO - Hepl
OK - thanks for information. I managed to take off the face of my '41 gauge. Just like the temperature gauge, it has two adjustment locations. One for zero set and one for range. I think I can...
|
Forum: Early V8 (1932-53)
09-18-2017, 03:05 PM
|
Replies: 27
Views: 9,708
|
Forum: Early V8 (1932-53)
09-18-2017, 01:54 PM
|
Replies: 27
Views: 9,708
|
Forum: Early V8 (1932-53)
09-18-2017, 01:24 PM
|
Replies: 27
Views: 9,708
Oil Pressure Sending Unit BO - Hepl
'41 passenger - 6V pos ground - I am having problems getting a working Oil Pressure Sending Unit. My last one, made in China, went bad. I ordered a new one from DC. Tested ohms when I got it. 11...
|
Forum: Early V8 (1932-53)
03-09-2017, 01:51 PM
|
Replies: 33
Views: 8,258
Re: Oversized O.D. Main Bearings
My machine guy says his dad (Machinist for Ford) told him about the ERP blocks. During the war, Ford would mass repair blocks by over boring because blocks were scarce. He thinks ERP stands for...
|
Forum: Early V8 (1932-53)
03-04-2017, 11:02 PM
|
Replies: 33
Views: 8,258
Re: Oversized O.D. Main Bearings
Update. I was able to find front and center at .010 under. Rear is reusable and machine guy will set crank to fit each bearing. I was able to find a rear at .020 under for next rebuild. I'm looking...
|
Forum: Early V8 (1932-53)
03-01-2017, 12:18 PM
|
Replies: 33
Views: 8,258
|
Forum: Early V8 (1932-53)
03-01-2017, 11:52 AM
|
Replies: 33
Views: 8,258
Re: Oversized O.D. Main Bearings
Thanks Richard - no luck with james, but nice guy. Flathead - I'm finding the same thing. My rebuilder is talking about shimming. Anyone tried that?
I'm trying Chuck now
|
Forum: Early V8 (1932-53)
02-28-2017, 11:15 PM
|
Replies: 33
Views: 8,258
|
Forum: Early V8 (1932-53)
01-27-2017, 02:12 PM
|
Replies: 33
Views: 8,258
|
Forum: Early V8 (1932-53)
01-27-2017, 09:48 AM
|
Replies: 33
Views: 8,258
|
Forum: Early V8 (1932-53)
01-26-2017, 10:32 PM
|
Replies: 33
Views: 8,258
|
Forum: Early V8 (1932-53)
01-26-2017, 05:26 PM
|
Replies: 33
Views: 8,258
|
Forum: Early V8 (1932-53)
01-26-2017, 04:20 PM
|
Replies: 33
Views: 8,258
Re: Oversized O.D. Main Bearings
There was not a part number and any indication that the OD was different. We ordered bearings assuming they would slip right in. Problem is they slip in to easily.
Where can I get a block?
|
Forum: Early V8 (1932-53)
01-26-2017, 03:25 PM
|
Replies: 33
Views: 8,258
Oversized O.D. Main Bearings
Can anyone confirm what I am hearing from my machinist? He was installing new main bearings in my '41 Sedan Coupe and says that the block and bearing caps have been line-bored 0.015 over original and...
|
Forum: Early V8 (1932-53)
07-04-2016, 02:32 PM
|
Replies: 2
Views: 914
|
Forum: Early V8 (1932-53)
07-04-2016, 01:39 PM
|
Replies: 2
Views: 914
|