Forum: Model A (1928-31)
02-07-2023, 12:12 AM
|
Replies: 32
Views: 12,113
|
Forum: Model A (1928-31)
01-11-2023, 06:43 PM
|
Replies: 11
Views: 1,573
Re: Canadian or international parts ordering
I regularly get items shipped to At The Border Storage in Sweetgrass. Once I have several items I will drive down and pick up the parts and bring them across the border. I end up paying the 5% GST...
|
Forum: Model A (1928-31)
01-04-2023, 06:24 PM
|
Replies: 10
Views: 1,995
Re: What is this Head
The model A head with a large cast B on the top of the head is the police head. This head uses the 4 bolt water pump.
The Model B head has a large C cast on top of the head and uses the 3 bolt...
|
Forum: Model A (1928-31)
12-07-2022, 07:09 PM
|
Replies: 21
Views: 2,908
Re: Roadster top upolstery
I have found that A1 foam and fabric sell the stayfast material which is very high quality top material. ...
|
Forum: Model A (1928-31)
11-29-2022, 09:26 PM
|
Replies: 99
Views: 29,702
|
Forum: Model A (1928-31)
11-26-2022, 04:52 PM
|
Replies: 71
Views: 10,238
Re: Supercharging a Model A
Some random thoughts.
Typically superchargers run a belt with "teeth" as shown in one of the attached photos.
There was a gentleman that pats on the HAMB that is running a supercharged model A....
|
Forum: Early V8
11-18-2022, 08:23 PM
|
Replies: 1
Views: 724
|
Forum: Model A (1928-31)
09-27-2022, 01:07 AM
|
Replies: 11
Views: 3,317
|
Forum: Model A (1928-31)
09-02-2022, 02:42 PM
|
Replies: 531
Views: 263,016
|
Forum: Model A (1928-31)
08-28-2022, 02:18 PM
|
Replies: 49
Views: 11,813
|
Forum: Early V8
08-15-2022, 08:47 PM
|
Replies: 1
Views: 724
LZ transmission gears
Looking for P.N. 26H-7017 L-Z Main Drive Gear - 19 Tooth
P.N. 01A-7100 Low-Reverse sliding gear - 29T helical (39-50) for 16 helical splines
P.N. 06H-7102 Intermediate (2nd) Gear - 24...
|
Forum: Model A (1928-31)
08-15-2022, 08:40 PM
|
Replies: 11
Views: 1,340
|
Forum: Model A (1928-31)
08-10-2022, 11:53 PM
|
Replies: 35
Views: 4,899
Re: Burtz Block
Increasing the Bore size increases the compression ratio, A standard bore engine verses a bored cylinder bore has a smaller volume then oversized bores and will result in a lower compression ratio. ...
|
Forum: Model A (1928-31)
07-26-2022, 11:18 PM
|
Replies: 9
Views: 1,722
|
Forum: Model A (1928-31)
03-22-2022, 07:31 PM
|
Replies: 82
Views: 11,030
Re: Autopsy of Broken "B" Engine
I lost a rod bearing many (50?) years ago. It was #3 rod bearing, original babbit bearing set to .0015" clearance. Driving to fast for a prolonged period on a hot summer's day was source of the...
|
Forum: Model A (1928-31)
03-20-2022, 05:01 PM
|
Replies: 29
Views: 6,031
|
Forum: Model A (1928-31)
03-10-2022, 06:43 PM
|
Replies: 15
Views: 2,337
Re: 238 mph
Interesting comments. I would have thought that with the stroke being the same, irrespective of rod length, that the piston must travel the same distance, and thus acceleration from TDC to BDC...
|
Forum: Model A (1928-31)
03-05-2022, 07:27 PM
|
Replies: 531
Views: 263,016
|
Forum: Model A (1928-31)
03-04-2022, 10:28 PM
|
Replies: 531
Views: 263,016
|
Forum: Model A (1928-31)
03-04-2022, 10:09 PM
|
Replies: 59
Views: 10,125
|
Forum: Model A (1928-31)
01-24-2022, 04:45 PM
|
Replies: 531
Views: 263,016
|
Forum: Model A (1928-31)
01-10-2022, 11:01 PM
|
Replies: 13
Views: 2,644
|
Forum: Model A (1928-31)
10-15-2021, 12:31 AM
|
Replies: 18
Views: 4,817
Re: Banger posi traction
Yes, the spool that Dan made is typically what was used by all the dirt track sprit cars running Ford V8 rear end gears in the Hallibrand 201 center sections. The sprit cars drifted around every...
|
Forum: Model A (1928-31)
07-29-2021, 12:48 AM
|
Replies: 531
Views: 263,016
|
Forum: Model A (1928-31)
07-28-2021, 09:17 PM
|
Replies: 531
Views: 263,016
|