Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 12 of 12
Search took 0.00 seconds. Search: Posts Made By: jglad
Forum: Model A (1928-31) 09-09-2023, 04:12 PM
Replies: 11
Views: 818
Posted By jglad
Re: top padding on huckster

I bought the top kit from Snyders and installed it using their padding. It came out looking good. Thanks for all the advice.
Forum: Model A (1928-31) 09-04-2023, 02:38 PM
Replies: 3
Views: 672
Posted By jglad
Re: Rear fender alteration

I have to do the same modification to the rear fenders for my huckster too. I think the best solution is to remove the 2 1/2 inches from the middle of the fender rather than the edge. That way you...
Forum: Model A (1928-31) 09-04-2023, 08:32 AM
Replies: 11
Views: 818
Posted By jglad
top padding on huckster

I am to the point on my huckster build where I am about to put the top material on. Should I use padding on top of the wooden slats or should I fasten the top material directly on the slats?
Forum: Model A (1928-31) 05-01-2023, 07:52 AM
Replies: 0
Views: 462
Posted By jglad
Subrail thickness at cowl

I am building a huckster with what I think is a 1931 Victoria cowl section. Can anyone tell me how thick the wooden subrail is where the cowl mounts to the frame.
Forum: Model A (1928-31) 04-19-2023, 07:23 AM
Replies: 6
Views: 873
Posted By jglad
Re: Wooden Subrail Question

So they used the same rubber pads that the cars with metal subrails and body blocks used?
Forum: Model A (1928-31) 04-19-2023, 06:41 AM
Replies: 6
Views: 873
Posted By jglad
Wooden Subrail Question

On the cars that used wooden subrails, did the wood rest directly on the side splash shields or was there some sort of pad in between.
Forum: Model A (1928-31) 01-07-2023, 04:41 PM
Replies: 8
Views: 1,617
Posted By jglad
Re: Separating driveshaft from pinion gear

Success. I used the pipe/big hammer method to separate the pinion from the driveshaft.
Forum: Model A (1928-31) 01-03-2023, 05:01 PM
Replies: 8
Views: 1,617
Posted By jglad
Separating driveshaft from pinion gear

I am in the process of rebuilding my differential and have run into a problem. The pinion/driveshaft is out of the differential and I am trying to separate them.
I have used my big gear puller...
Forum: Model A (1928-31) 09-04-2021, 07:28 AM
Replies: 7
Views: 1,941
Posted By jglad
Re: 1930 Tudor Top installation

Thanks everyone for the all the help. I have a follow up question about how the chicken wire and padding go on the front header. I am assuming the chicken wire fastens on top of the header behind...
Forum: Model A (1928-31) 08-31-2021, 10:47 AM
Replies: 7
Views: 1,941
Posted By jglad
1930 Tudor Top installation

I am about to install a new top kit on my 1930 Tudor. Should the padding under the top cover just the chicken wire or should it extend across the metal on the sides down to the drip rail?
Forum: Model-A 08-25-2021, 05:24 PM
Replies: 1
Views: 750
Posted By jglad
Re: 1930-31 rear sedan fenders

I still need the fenders. If you have a set I can be reached at jgladf1930 at gmail dot com. I can't respond to PMs on this site.
Forum: Model-A 07-28-2021, 06:24 AM
Replies: 1
Views: 750
Posted By jglad
1930-31 rear sedan fenders

Needing a pair of rear fenders for a 1930-31 tudor sedan.
Showing results 1 to 12 of 12

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:59 AM.