Forum: Model A (1928-31)
Today, 12:37 PM
|
Replies: 3
Views: 136
Re: Positive ground tach
see attached.
https://www.santaanitaas.org/wp-content/uploads/2018/10/4-Tachometer.pdf
Tom Endy
|
Forum: Model A (1928-31)
04-08-2024, 11:54 AM
|
Replies: 18
Views: 1,006
Re: Differential Pinion Gear Bearing Preload
When I first started rebuilding Model A differentials back in 1988, I researched all the literature I could find in the Model A kingdom. Information written in the day by old Model A guys recommended...
|
Forum: Model A (1928-31)
04-08-2024, 11:15 AM
|
Replies: 20
Views: 993
Re: Leaking gas tank
Whatever you do to seal the tank, it is prudent to install the later steering column mount to take pressure off the one riveted to the tank. When we restored my grandson's 1930 Tudor, we installed...
|
Forum: Model A (1928-31)
04-08-2024, 10:48 AM
|
Replies: 14
Views: 735
Re: Condenser Capacity
Attached is what I have discovered.
https://www.santaanitaas.org/wp-content/uploads/2023/04/Change-the-Condenser-rev-2023.pdf
Tom Endy
|
Forum: Model A (1928-31)
04-03-2024, 11:58 AM
|
Replies: 5
Views: 317
Re: brake pedal
The last page of the attached article describes how to even the pedals.
https://www.santaanitaas.org/wp-content/uploads/2022/07/Bell-Housing-Restoration-Color-Version.pdf
Tom Endy
|
Forum: Model A (1928-31)
04-01-2024, 12:33 AM
|
Replies: 7
Views: 407
Re: Wheel Bearing Part #’s
Attached!
https://www.santaanitaas.org/wp-content/uploads/2022/11/Model-A-Bearing-Part-Numbers.pdf
Tom Endy
|
Forum: Model A (1928-31)
03-30-2024, 07:17 PM
|
Replies: 8
Views: 584
Re: So Cal radiator repair shop
Tom's Radiator shop
828 W. Chapman
Orange, CA 92868
714-532-6771
tomsradiatororange.com
The City of Orange is about 40 miles south of Pasadena. It is where the famous Model A pancake...
|
Forum: Model A (1928-31)
03-30-2024, 04:06 PM
|
Replies: 25
Views: 1,443
|
Forum: Model A (1928-31)
03-30-2024, 11:21 AM
|
Replies: 9
Views: 552
Re: Ring gear replacement
The attached article may help.
http://www.santaanitaas.org/wp-content/uploads/2014/08/flywheel-ring-gear.pdf
Tom Endy
|
Forum: Model A (1928-31)
03-25-2024, 07:10 PM
|
Replies: 22
Views: 1,264
Re: Fuse blowing
This may help. Also check the terminal block on the firewall. The repose often allows the head of each screw to back off at the back and touch the firewall and short out.
...
|
Forum: Model A (1928-31)
03-25-2024, 04:42 PM
|
Replies: 33
Views: 10,085
Re: How to grease leaf springs?
Here is how we did it to the rear spring on my grandsons 1930 Tudor.
https://www.santaanitaas.org/wp-content/uploads/2024/01/Spring-restoration-PDF.pdf
Tom Endy
|
Forum: Model A (1928-31)
03-25-2024, 03:58 PM
|
Replies: 9
Views: 742
|
Forum: Model A (1928-31)
02-24-2024, 10:58 AM
|
Replies: 17
Views: 742
|
Forum: Model A (1928-31)
02-23-2024, 06:41 PM
|
Replies: 17
Views: 742
Re: pinion gear double cup bearing issue
The reason the double pinion bearing race fell out during disassembly is because it had spun in the banjo housing mounting. You can see the spin marks in the banjo photo. This is because the last...
|
Forum: Model A (1928-31)
02-22-2024, 04:38 PM
|
Replies: 5
Views: 638
Re: Rear End Rebuild Advice/Help Needed
I agree.
The trick is to torque only the right side. Then install the carrier and start running the bolts down on the left side evenly and turn the ring gear with your finger until you feel it...
|
Forum: Model A (1928-31)
02-22-2024, 01:59 AM
|
Replies: 5
Views: 638
Re: Rear End Rebuild Advice/Help Needed
Denny:
You need to add more shims under the bearings on each side of the carrier to be able to install at least one .010 paper gasket on each side of the banjo to achieve the proper pre-load,...
|
Forum: Model A (1928-31)
02-19-2024, 12:54 AM
|
Replies: 10
Views: 734
Re: Carb Disassembly Tips
Be very careful with the disassembly. A lot of good Zeniths have been destroyed during disassembly. The attached document should guide you through it.
...
|
Forum: Model A (1928-31)
02-18-2024, 05:37 PM
|
Replies: 5
Views: 787
Re: Original Ford wrench question
There is another set of original Ford wrenches that is not often seen. These were probably mostly used at the Ford dealerships. I found a set at the Turlock swap meet years ago and have used them...
|
Forum: Model A (1928-31)
02-06-2024, 07:08 PM
|
Replies: 26
Views: 4,984
Re: Mitchell Overdrive
Only the later Mitchell overdrives have these grease fittings. The only lubrication on the older ones is the gear oil that you need to change periodically. The two grease fittings on the later ones...
|
Forum: Model A (1928-31)
02-05-2024, 08:45 PM
|
Replies: 22
Views: 1,849
counter balanced crank
Is there a supplier in the Model A Kingdom offering a counter balanced crank? Years ago, there was an engine shop in Whittier California offering such. The owner died a number of years ago and the...
|
Forum: Model A (1928-31)
01-28-2024, 06:34 PM
|
Replies: 8
Views: 695
|
Forum: Model A (1928-31)
01-26-2024, 06:46 PM
|
Replies: 13
Views: 827
Re: Pressure Plate Fingers
If you are using a Model A pressure plate, be sure to check the step on the flywheel where the pressure plate bolts up. The original depth is 1.123", Often a flywheel was resurfaced without the same...
|
Forum: Model A (1928-31)
01-26-2024, 11:34 AM
|
Replies: 13
Views: 827
Re: Pressure Plate Fingers
As the fellow above says, it must be a fully assembled clutch attached to the flywheel. The measurement is from the flat surface of the pressure plate to the top of each finger.
...
|
Forum: Model A (1928-31)
01-25-2024, 08:15 PM
|
Replies: 4
Views: 640
Re: Model B Oil Tube?
A Model B breather tube will fit a Model A engine. I put one on my grandson's 30 Tudor about a year ago. At the time all the suppliers were out of stock for the repos. I got an original from Sammy at...
|
Forum: Model A (1928-31)
01-22-2024, 05:26 PM
|
Replies: 40
Views: 2,946
Re: Tow Insurance
Get some old Model A guys to help you push it out of your garage onto the street and then call AAA to come and take it to a shop.
Tom Endy
|