Forum: Early V8
06-12-2022, 10:06 PM
|
Replies: 0
Views: 290
1941 car steering column
Sold - For sale is a 1941 Ford car steering column and three on the tree column shift shaft mechanism. There is no inner steering shaft, or box. The key and column lock mechanism is froze up. ...
|
Forum: Early V8
04-25-2022, 12:48 PM
|
Replies: 0
Views: 348
1950 Ford driveshaft, yoke and universal
For sale is an open drive driveshaft from a 1950 Ford 4 door car. It was mated to a Flathead V8 with a three speed side shift transmission. It includes the front yoke and the rear universal joint....
|
Forum: Early V8 (1932-53)
04-17-2022, 09:01 AM
|
Replies: 106
Views: 9,254
Re: 89 today
Happy birthday Ron. Thank you for sharing your knowledge with so many around the world.
|
Forum: Early V8 (1932-53)
02-18-2022, 11:23 AM
|
Replies: 40
Views: 6,648
|
Forum: Early V8
01-12-2022, 01:01 PM
|
Replies: 3
Views: 498
|
Forum: Early V8
01-12-2022, 12:56 PM
|
Replies: 3
Views: 498
|
Forum: Early V8
01-12-2022, 12:55 PM
|
Replies: 3
Views: 498
|
Forum: Early V8 (1932-53)
01-09-2022, 06:21 PM
|
Replies: 7
Views: 1,728
Re: Ahooga horn
I did find a Hutchins horn today. Thanks for that suggestion.
|
Forum: Early V8 (1932-53)
12-31-2021, 12:41 PM
|
Replies: 7
Views: 1,728
Ahooga horn
Who makes the best authentic sounding 12 volt Ahooga horn? Many on the market and most with reviews indicate terrible sound.
|
Forum: Early V8 (1932-53)
12-15-2021, 02:34 PM
|
Replies: 8
Views: 1,110
Re: Ford Carburetor question
You know Alan, I read that somewhere in a blog that listed the different model numbers of 94’s, what years they were used, on cars or trucks etc. and it had a few comments here and there about each. ...
|
Forum: Early V8 (1932-53)
11-14-2021, 06:37 PM
|
Replies: 8
Views: 1,110
Re: Ford Carburetor question
From what I’ve read, the 8BA was used in 1949 and had been considered to have better flow than previous years. That would be my choice.
|
Forum: Early V8
11-13-2021, 09:44 AM
|
Replies: 0
Views: 448
‘49-‘51 V8 8BA bell housing / starter plate
SOLD. Steel stamped bell housing with starter plate and linkage parts for 1949 - 1951 Ford Flathead 8BA engine. Shipping charges not included and are the responsibility of the buyer. UPS charges...
|
Forum: Early V8
11-09-2021, 10:14 AM
|
Replies: 0
Views: 514
Ford flathead Open Drive Trans mount & Trans shaft
Ford Open Drive Trans Mount: This was used with Ford 3 speed transmission to allow for an open drive driveshaft (no torque tube) on 1942 - 1952 Fords. Set up allows for conversion to open drive on...
|
Forum: Early V8
11-09-2021, 10:08 AM
|
Replies: 3
Views: 819
|
Forum: Early V8
10-17-2021, 09:58 AM
|
Replies: 0
Views: 383
Grille bug guard
Not sure what this came off of. Appears to be a bug catcher that was mounted over the cars radiator grille. Seems to have a shape similar to a 1934 - 1937 Ford but not sure. Used condition with...
|
Forum: Early V8
10-16-2021, 03:55 PM
|
Replies: 0
Views: 554
Ford flathead truck oil pan
1948 - 1952 Ford truck oil pan. Highly sought after flathead pan due to the rear sump and clean out on bottom of pan. Pan is in good original condition, with no dents and nice straight rails. Just...
|
Forum: Early V8
10-16-2021, 03:16 PM
|
Replies: 3
Views: 498
Oil pan 1949 - 1953
1949 - 1953 Ford Flathead V8 oil pan. Standard center sump. Includes sump pick up, drain plug and dip stick (no tube). This pan has been cleaned and painted. It came off a fresh rebuild that went...
|
Forum: Early V8
10-16-2021, 11:34 AM
|
Replies: 1
Views: 703
|
Forum: Early V8
10-13-2021, 02:54 PM
|
Replies: 1
Views: 703
Ford flathead top loader transmission - Sold
Sold - For sale this 78-7006 Ford Flathead 3 speed top loader transmission. For use as parts; it includes a two 5/8” decent 81A-7222 later style shifter tower and a rusty gear set that is stuck...
|
Forum: Early V8
10-12-2021, 11:34 AM
|
Replies: 3
Views: 819
Re: 1937 Ford bumper
Update. I was able to crop and finally upload a few photos. Again I can email more if your interested.
|
Forum: Early V8
10-12-2021, 11:23 AM
|
Replies: 3
Views: 819
Re: 1937 Ford bumper
The system will not accept the photos so if interested, I would be happy to email the photos to you. Sorry bout that.
|
Forum: Early V8
10-12-2021, 11:21 AM
|
Replies: 3
Views: 819
1937 Ford bumper - sold
SOLD. - For sale is this 1937 Ford bumper that came off my 1937 Ford coupe. I do not recall if this was the front or rear bumper as one of the two bumpers removed was used in another project. The...
|
Forum: Early V8 (1932-53)
02-05-2021, 12:06 PM
|
Replies: 12
Views: 2,324
|
Forum: Early V8 (1932-53)
01-26-2021, 06:10 PM
|
Replies: 12
Views: 2,324
Re: External oil filter - question on oil lines
Sorry for any confusion. I’m not mounting the original filter on the head, but rather on the firewall so I need to use a flexible line. I was hoping to get confirmation on the fittings and thread...
|
Forum: Early V8 (1932-53)
01-26-2021, 03:35 PM
|
Replies: 12
Views: 2,324
External oil filter - question on oil lines
I have mounted my external oil filter on the firewall and will need to buy flexible oil lines with the correct connection ends. I know that Ford used different types of threads etc. and so I’m...
|